Mimaki CG-75FX CG-130FX CG-160FX Service Manual and Parts List Manual

Service Manual and Parts List Manual Mimaki CG-75FX CG-130FX CG-160FX;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Mimaki cuttig plotter.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Mimaki CG-75FX CG-130FX CG-160FX cutting plotter. You can find easily everything what do you need.
To see what contain, please read table of contents:

Content for Service Manual:
CHAPTER 1. OUTLINE OF MAINTENANCE
1-1. Precautions in Maintenance
1-2. Tools required for maintenance work
1-3. Specifications of the main unit

CHAPTER 2. DISASSEMBLY AND REPLACEMENT
2-1. Keyboard PCB assembly
2-2. Y cover
2-3. Side covers
2-4. X motor, M pulley
2-5. Pen assembly, Light pointer
2-6. Auto cutter assembly
2-7. Mark assembly
2-8. Y drive belt, Tension pulley assembly
2-9. Y motor
2-10. Clamp sensor
2-11. Mark PCB M assembly (75FX, 130FX, 160FX (After Rev.3))
2-12. SUB PCB assembly (160FX (Before Rev.2))
2-13. Mark PCB H assembly
2-14. Main PCB assembly (75FX, 130FX, 160FX (After Rev.3))
2-15. Main PCB assembly (160FX (Before Rev.2))
2-16. Power supply unit
2-17. Paper Sensor assembly
2-18. DC fan motor assembly
2-19. Pully BRG

CHAPTER 3. EXPLANATION OF ELECTRICAL SECTION
3-1. Locations of PCB’s
3-2. Explanation of PCB’s
3-2-1. Power supply PCB
3-2-2. Main PCB (75FX, 130FX, 160FX (After Rev.3))
3-2-3. Main PCB (160FX (Before Rev.2))
3-2-4. Keyboard PCB
3-2-5. Pen flexible PCB
3-2-6. Mark PCB H
3-2-7. Mark PCB M (75FX, 130FX, 160FX (After Rev.3))
3-2-8. Sub PCB (160FX (Before Rev.2))
3-3. Electronic diagram

CHAPTER 4. TROUBLESHOOTING
4-1. Troubles that result in displaying of error messages
4-1-1. List of messages, Warnings, Status displays
4-1-2. Corrective measures
4-2. Troubles without error messages displayed

CHAPTER 5 ADJUSTMENT ITEMS/ADJUSTMENT PROCEDURE
5-1. List of adjustments
5-2. List of meintenance items
5-3. Opening of meintenance items
5-4. Adjustment of #ADJUSTMENT items
5-4-1. $ZI COMMAND
5-4-2. $PEN No. ASSIGNMENT
5-4-3. $BUFFER DUMP
5-4-4. $400mm SQUARE
5-4-5. $PEN PRESSURE
5-4-6. $PEN LANDING
5-4-7. $MOTOR CURRENT
5-4-8. $AUTO CUT ADJUST
5-4-9. Adjusting the location of mark sensor
5-4-10. $PHOTO SENSOR (Photo Sensor Sensitivity Adjustment)
5-4-11. $PHOTO SENSOR (Adjusting the position of photo sensor)
5-4-12. $ DEFAULT SET
5-4-13. X-axis timing belt tension adjustment
5-4-14. Y-axis timing belt tension adjustment
5-4-15. Auto cutter position adjustment
5-4-16. Output voltage adjustment
5-5. #TEST items
5-5-1. & LOOP BACK
5-5-2. & HANDSHAKE
5-5-3. &TEST PATTERN
5-5-4. &FEED TEST 2m / &FEED TEST 10m
5-5-5. &PARAMETER DRAW
5-5-7. & A SERVO TEST
5-5-6. &PARAMETER DRAW 2
5-5-8. &B SERVO TEST
5-5-9. &AB SERVO TEST
5-5-10. &AUTO CUTTER
5-5-11. &SENSOR TEST
5-5-12. &KEYBOARD TEST
5-5-13. &DISPLAY TEST
5-5-14. &LCD TEST
5-5-15. &ROM/RAM CHECK
5-6. System parameter

CHAPTER 6. APPENDIX
6-1. Maintenance operation flow
6-2. Initial operation flow
6-3. Sheet detection flow
6-4. Mark detection operation flow
6-4-1. Mark detection overview (after sheet detection, at 4-point Mark detection)
6-5. Updating the firmware
6-6. CG-FX Series updating procedure
6-6-1. Checking the contents of updating file
6-6-2. Updating the firmware for plotter

——————-

Content for Parts List Manual:
0. RECOMMENDED PARTS LIST
1. K/B, Y-Bar ASSY.
2. Cover ASSY.
3. Pen ASSY.
4. Mark, Cutter ASSY.
5. Slider ASSY.
6. Frame ASSY.
7. X-drive ASSY.(75FX/75FXII)
8. X-drive ASSY.(130FX/130FXII)
9. X-drive ASSY.(160FX/160FXII)
10. Y-drive ASSY.
11. Clamp ASSY.(75/130/FX/FXII)
12. Clamp ASSY.(160/FX/FXII)
13. Main PCB ASSY.
14. Stand ASSY.
15. Roll ASSY.