Roland VersaCAMM VS-640i VS-540i VS-300i Service Manual and Parts List Manual

Service Manual and Parts List Manual Roland VersaCAMM VS-640i VS-540i VS-300i;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland VersaCAMM.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland VersaCAMM VS-640i VS-540i VS-300i. You can find easily everything what do you need.
To see what contain, please read table of contents:

1) Structure & Spare Parts
OVERVIEW
1-1 COVER
1-2 PANEL
1-3 FRAME
1-4 LEVER
1-5 BED
1-6 RAIL
RAIL-VS-640i-
RAIL-VS-540i-
RAIL-VS-300i-
1-7 CHASSIS
1-8 SCAN MOTOR
1-9 FEED MOTOR
1-10 HEAD CARRIAGE
1-11 TOOL CARRIAGE
1-12 WIPER
1-13 CAP
1-14 PUMP
1-15 INK CARTRIDGE
1-16 CHOKE VALVE
1-17 CIRCULATION PUMP
1-18 INK TUBE WIRING
1-19 PINCH ROLLER
1-20 STAND
1-21 ACCESSORY 1
1-22 ACCESSORY 2

2) Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 SERVO BOARD
2-4 CARRAGE BOARD
2-5 SUB BOARD

3) Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 DAMPER REPLACEMENT
3-3 WIPER REPLACEMENT
3-4 FELT WIPER REPLACEMENT
3-5 WIPER SCRAPER REPLACEMENT
3-6 CAP TOP REPLACEMENT
3-7 TOOL CARRIAGE REPLACEMENT
3-8 CARRIAGE MOTOR REPLACEMENT
3-9 FEED MOTOR REPLACEMENT
3-10 PUMP REPLACEMENT
3-11 BOARD REPLACEMENT (MAIN BOARD)
3-12 SW POWER SUPPLY REPLACEMENT
3-13 BATTERY REPLACEMENT
3-14 CARRIAGE BELT REPLACEMENT
3-15 ENCODER SCALE REPLACEMENT
3-16 GRIT ENCODER REPLACEMENT
3-17 PINCH ROLLER REPLACEMENT
3-18 CUTTER PROTECTION REPLACEMENT
3-19 CUT RIBBON CABLE REPLACEMENT
3-20 LINEAR ENCODER BOARD REPLACEMENT
3-21 HOW TO FOLD RIBBON CABLE TO THE HEAD
3-22 RIBBON CABLE (MAIN BOARD TO CARRIAGE BOARD) REPLACEMENT

4) Adjustment
4-1 SERVICE MODE
4-2 HOW TO UPGRADE/INSTALL FIRMWARE
4-3 HEAD ALIGNMENT
4-4 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
4-5 LINEAR ENCODER SETUP
4-6 FLUSHING POSITION ADJUSTMENT
4-7 CROP MARK SENSOR ADJUSTMENT
4-8 CROP-CUT ADJUSTMENT
4-9 PRINT/CUT POSITION ADJUSTMENT
4-10 CALIBRATION(FEEDING DIRECTION)
4-11 TOOL HEIGHT ADJUSTMENT
4-12 TOOL PRESSURE ADJUSTMENT
4-13 BELT TENSION ADJUSTMENT
4-14 BELT POSITION ADJUSTMENT
4-15 TAKE-UP UNIT OPERATION CHECK

5) Supplemental Information
5-1 SPECIAL TOOLS
5-2 SENSOR MAP
5-3 MOTOR ERROR
5-4 SERVICE CALL

6) Service Activities
6-1 INSTALLATION CHECK LIST
6-2 MAINTENANCE CHECK LIST
6-3 SPECIFICATION

VS640i VS540i VS300i VS 640i VS 540i VS 300i