Brother ADS-1500W/ADS-1600W Service Manual and Parts List Manual

Service Manual and Parts List Manual Brother ADS-1500W/ADS-1600W;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Brother.
You can print, zoom or read any diagram, picture or page from this manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Brother photocopier.
To see what contain, please read table of contents:

PRODUCT WARRANTY & LIABILITY
REGULATION
SAFETY INFORMATION

CHAPTER 1) SPECIFICATIONS
1. SPECIFICATIONS LIST
1.1 General
1.2 Network Connectivity
1.3 Service Information
1.4 Consumable Parts
1.5 Paper
1.5.1 Paper handling
1.5.2 Media specifications
1.6 Scanner

CHAPTER 2) ERROR INDICATIONS & TROUBLESHOOTING
1. CHECKS BEFORE COMMENCING TROUBLESHOOTING
2. OVERVIEW
2.1 Cross-section Drawing
2.2 Paper Feeding
2.3 Operation of Each Part
2.4 Block Diagram
2.5 Main Components
3. ERROR INDICATIONS
3.1 Error Codes
3.2 Error Messages
4. TROUBLESHOOTING
4.1 Error Cause and Remedy
4.2 Troubleshooting for Image Defects
4.2.1 Defect examples
4.2.2 Troubleshooting according to image defect
4.3 Troubleshooting for Document / Card Feeding Problems
4.3.1 Multiple documents are fed
4.3.2 Document becomes wrinkled
4.3.3 Document becomes jammed
4.3.4 Card becomes jammed
4.3.5 Document is not picked up and fed
4.3.6 Card is not picked up and fed
4.4 Troubleshooting for Software Problems
4.4.1 Does not respond to operation from a computer
4.4.2 Cannot read data
4.5 Troubleshooting for Control Panel Problems
4.5.1 Nothing is displayed on the LCD
4.5.2 Power key is inoperable
4.5.3 Touch panel is inoperable
4.6 Troubleshooting for Network Problems
4.6.1 Cannot scan via network connection
4.7 Troubleshooting for Other Problems
4.7.1 Machine is not turned ON
4.7.2 Unusual noise is coming from the machine
4.7.3 Cannot save data in USB flash memory drive
4.7.4 Cannot reset counters for periodic replacement parts
4.7.5 A non-supported USB device is connected to the USB terminal

CHAPTER 3) DISASSEMBLY/REASSEMBLY
1. PACKING
2. SCREW CATALOGUE
3. SCREW TORQUE LIST
4. LUBRICATION
5. OVERVIEW OF GEARS
6. HARNESS ROUTING
7. DISASSEMBLY FLOW CHART
8. DISASSEMBLY PROCEDURE
8.1 Preparation
8.1.1 Backup of the machine information and head correction data
(When replacing the main PCB ASSY)
8.1.2 Disconnecting cables
8.2 Bottom rubber
8.3 Side cover L
8.4 Side cover R
8.5 Front under cover
8.6 Back cover
8.7 Top cover ASSY / Guide tray ASSY
8.8 Main PCB ASSY
8.9 Wireless LAN PCB ASSY / Gasket / Wireless LAN PCB support
8.10 Front cover L
8.11 Panel unit
8.12 Second side CIS unit
8.13 Separation pad ASSY
8.14 Second side CIS flat cable
8.15 Document scanning position sensor PCB / Document detection sensor PCB /
Card scanning position sensor PCB
8.16 Main motor
8.17 Ejection roller cover
8.18 First side CIS unit
8.19 Pick-up roller cover ASSY
8.20 Pick-up roller
8.21 Cover switch ASSY
8.22 First side CIS flat cable
8.23 Card detection sensor PCB

CHAPTER 4) ADJUSTING AND UPDATING SETTINGS AS REQUIRED AFTER
PARTS REPLACEMENT
1. IF YOU REPLACE THE MAIN PCB ASSY
1.1 Checking Firmware Version
1.2 Setting by Country
1.3 CIS Type Setting (function code: 59)
1.4 Installing Firmware
1.5 Initializing the EEPROM of the Main PCB ASSY (function code: 01)
1.6 Restoring Machine Information (function code: 46)
1.7 Setting Serial Numbers
1.8 Acquiring White Level Data (function code: 55)
1.9 Adjusting Touch Panel (function code: 78)
1.10 Checking Operation after Repair
2. IF YOU REPLACE THE CIS UNIT
2.1 Checking Firmware Version
2.2 CIS Type Setting (function code: 59)
2.3 Installing Firmware
2.4 Acquiring White Level Data (function code: 55)
2.5 Checking Operation after Repair
3. IF YOU REPLACE THE PANEL UNIT
3.1 Adjusting Touch Panel (function code: 78)
3.2 Checking LCD Operation (function code: 12)
3.3 Checking Control Panel Operation (function code: 13)
4. IF YOU REPLACE THE PICK-UP ROLLER / SEPARATION PAD ASSY
4.1 Resetting Pick-up Roller / Separation Pad Counters

CHAPTER 5) SERVICE FUNCTIONS
1. MAINTENANCE MODE
1.1 How to Enter Maintenance Mode
1.1.1 Method of entering end-user accessible maintenance mode
1.1.2 Method of entering maintenance mode for service personnel
1.2 List of Maintenance Mode Functions
1.3 Details of Maintenance Mode Functions
1.3.1 Initialize EEPROM parameters (function code: 01, 91)
1.3.2 ADF performance test (function code: 08)
1.3.3 Set worker switches (WSW) (function code: 10)
1.3.4 Check LCD operation (function code: 12)
1.3.5 Check control panel key operation (function code: 13)
1.3.6 Save Net Config Print as text (function code: 18)
1.3.7 Update firmware using USB flash memory drive (function code: 28)
1.3.8 Check sensor operation (function code: 32)
1.3.9 Backup machine information (function code: 46)
1.3.10 Fine-tune scanning position (function code: 54)
1.3.11 Acquire white level data and set CIS scan area (function code: 55)
1.3.12 Set CIS type (function code: 59)
1.3.13 Setting by country (function code: 74)
1.3.14 Register maintenance information (function code: 77)
1.3.15 Adjust touch panel (function code: 78)
1.3.16 Display machine log information (function code: 80)
1.3.17 Display machine error code (function code: 82)

CHAPTER 6) WIRING DIAGRAM
1. WIRING DIAGRAM

CHAPTER 7) PERIODICAL MAINTENANCE
1. PERIODICAL MAINTENANCE PARTS

APPENDIX 1 SERIAL NUMBERING SYSTEM
APPENDIX 2 DELETING USER SETTING INFORMATION
APPENDIX 3 INSTALLING THE MAINTENANCE PRINTER DRIVER

Parts List Manual.

Brother ADS-1500W ADS-1600W ADS-1500 ADS-1600 ADS1500W ADS1600W ADS 1500W ADS 1600W ADS1500 ADS1600