Brother ADS-2800W ADS-3600W Service Manual and Parts List Manual

Service Manual and Parts List Manual Brother ADS-2800W/ADS-3600W;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Brother advanced document scanner.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Brother ADS-2800W/ADS-3600W. You can find easily everything what do you need.
To see what contain, please read table of contents:

SAFETY INFORMATION
CHAPTER 1. SUPPLEMENTAL SPECIFICATIONS
1. GENERAL
2. NETWORK CONNECTIVITY
3. SERVICE INFORMATION
4. CONSUMABLE PARTS
5. PAPER
5.1 Paper Handling
5.2 Media Specifications
6. SCANNER

CHAPTER 2. ERROR INDICATIONS & TROUBLESHOOTING
1. INTRODUCTION
1.1 Precautions
1.2 Checks before Commencing Troubleshooting
2. OVERVIEW
2.1 Cross-section Drawing
2.2 Paper Feeding
2.3 Operation of Each Part
2.4 Block Diagram
2.5 Main Components
3. ERROR INDICATIONS
3.1 Error Codes
3.2 Error Messages
4. TROUBLESHOOTING
4.1 Error Cause and Remedy
4.2 Troubleshooting for Image Defects
4.2.1 Defect examples
4.2.2 Troubleshooting according to image defect
4.3 Troubleshooting for Document Paper Feeding Problems
4.3.1 No document is fed
4.3.2 Multiple documents are fed
4.3.3 Document becomes jammed
4.3.4 Document becomes wrinkled
4.4 Troubleshooting for Software Problems
4.4.1 Does not respond to operation from a computer
4.4.2 Cannot read data
4.5 Troubleshooting for Control Panel Problems
4.5.1 Nothing is displayed on the LCD
4.5.2 Control panel is inoperable
4.6 Troubleshooting for Network Problems
4.6.1 Cannot scan via network connection
4.6.2 Cannot connect to access point
4.7 Troubleshooting for Other Problems
4.7.1 Machine does not turn ON
4.7.2 Cannot update firmware
4.7.3 Cannot save data in USB flash memory
4.7.4 USB device connection error
4.7.5 Cannot register
4.7.6 Counter does not reset even the consumable part has been replaced
4.7.7 Installation using USB flash memory is not operable

CHAPTER 3. DISASSEMBLY/REASSEMBLY
1. SAFETY PRECAUTIONS
2. PACKING
3. SCREW CATALOGUE
4. SCREW TORQUE LIST
5. LUBRICATION
6. OVERVIEW OF GEARS
7. HARNESS ROUTING
8. DISASSEMBLY FLOW CHART
9. DISASSEMBLY PROCEDURE
9.1 Reverse roller / Pick up roller
9.2 Bottom cover ASSY / Exit stopper
9.3 Back cover
9.4 Side cover L/R
9.5 Wireless LAN PCB ASSY
9.6 USB host PCB ASSY
9.7 Main PCB ASSY
9.8 Front cover L/R
9.9 Front cover ASSY
9.10 Panel unit / Panel flat cable / Panel PCB / LCD / Touch panel unit / NFC PCB ASSY
9.11 Second side CIS unit / Second side CIS flat cable / Flat cable support film
9.12 Eject jam sensor PCB
9.13 Document scanning position sensor PCB
9.14 Paper feed jam sensor PCB / Multi feeding sensor PCB ASSY (Sent)
9.15 Document detection sensor PCB ASSY
9.16 First side CIS unit / First side CIS flat cable
9.17 Front cover sensor
9.18 Feed belt / Feed motor
9.19 Paper feed belt / Paper feed motor
9.20 Multi feeding sensor PCB ASSY (Receive)

CHAPTER 4. ADJUSTING AND UPDATING SETTINGS AS REQUIRED AFTER PARTS REPLACEMENT
1. IF YOU REPLACE THE MAIN PCB ASSY
1.1 Installing Firmware (Sub3 Firm / Main Firm)
1.1.1 Checking firmware version
1.1.2 Installing firmware
1.2 Adjust Touch Panel
1.3 Setting by Country
1.4 Initializing the EEPROM of the Main PCB ASSY
1.5 Setting Serial Number
1.6 Setting Multi Feeding Sensor Threshold
1.7 Check Sensor Operation
1.8 Check Multi Feeding Operation
1.9 Checking Operation after Repair
1.10 Resetting to Factory Shipping State
2. IF YOU REPLACE THE CIS UNIT
2.1 Acquire White Level Data and Set CIS Scan Area
2.2 Checking Operation after Repair
3. IF YOU REPLACE THE MULTI FEEDING SENSOR
3.1 Setting Multi Feeding Sensor Threshold
3.2 Check Multi Feeding Operation
3.3 Checking Multi Feeding Sensor Operation
4. IF YOU REPLACE THE PANEL ASSY
4.1 Adjusting Touch Panel
4.2 Checking LCD Operation
4.3 Checking Control Panel Operation
5. IF YOU REPLACE THE PICK UP ROLLER / REVERSE ROLLER
5.1 Resetting Pick Up Roller / Reverse Roller Counters

CHAPTER 5. SERVICE FUNCTIONS
1. MAINTENANCE MODE
1.1 How to Enter Maintenance Mode
1.1.1 Method of entering maintenance mode for service personnel
1.1.2 Method of entering end-user accessible maintenance mode
1.2 List of Maintenance Mode Functions
1.3 Details of Maintenance Mode Functions
1.3.1 Initialize EEPROM parameters (function code: 01, 91)
1.3.2 ADF performance test (function code: 08)
1.3.3 Set worker switches (WSW) (function code: 10)
1.3.4 Check LCD operation (function code: 12)
1.3.5 Check control panel key operation (function code: 13)
1.3.6 Save NetConfig data (function code: 18)
1.3.7 Display software version (function code: 25)
1.3.8 Acquire machine log information (function code: 31)
1.3.9 Check sensor operation (function code: 32)
1.3.10 Change USB No. return value (function code: 45)
1.3.11 Fine-tune scanning position (function code: 54)
1.3.12 Acquire white level data and set CIS scan area (function code: 55)
1.3.13 Adjust touch panel (function code: 61)
1.3.14 Setting by country (function code: 74)
1.3.15 Display machine log information (function code: 80)
1.3.16 Display machine error code (function code: 82)
1.3.17 Quit maintenance mode (function code: 99)

CHAPTER 6. WIRING DIAGRAM
1. WIRING DIAGRAM

CHAPTER 7. PERIODICAL MAINTENANCE
1. PERIODICAL MAINTENANCE PARTS

APPENDIX 1 SERIAL NUMBERING SYSTEM
APPENDIX 2 DELETING USER SETTING INFORMATION
APPENDIX 3 INSTALLING THE MAINTENANCE PRINTER DRIVER

Parts List Manual

Brother ADS2800W ADS3600W BrotherADS2800W BrotherADS3600W