Graphtec CE3000 series Service Manual and Parts List Manual

This service manual cover models:
CE3000-40/60/120/120AP/CE2800/SSK/CE3500
CE3000-40Mk2/60Mk2/120Mk2
CE3000-40CRP (Craft ROBO Pro)

This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Graphtec.
You can print, zoom or read any diagram, picture or page from this manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Graphtec CE3000 series Service Manual and Parts List Manual.
Table of contents:

1. INTRODUCTION
1.1 Main Specifications
1.2 External Dimensions

2. PARTS NAMES and FUNCTIONS
2.1 Parts Names and Functions
2.2 Assembling the Stand
2.3 Attaching the Basket (CE3000-60/120: Optional)

3. OPERATIONS
3.1 Control Panel
3.2 Menu List
3.3 Description of Special Functions A
3.4 Description of Special Functions B

4. RECOMMENDED PARTS LIST

5. LIST OF TOOLS
5.1 Tools
5.2 Greasing And Gluing Points
5.3 Subparts List

6. DISASSEMBLY AND REASSEMBLY
6.1 Exterior Parts
6.1.1 How to Replace the Right Side Cover
6.1.2 How to Replace the Left Side Cover
6.1.3 How to Replace the Center Cover
6.1.4 How to Replace the Front Guide (CE3000-40/60)
6.1.5 How to Replace the Front Guide (CE3000-120)
6.1.6 How to Replace the Rear Guide
6.2 Mechanical Parts
6.2.1 How to Replace the Front and Rear Media Sensors
6.2.2 How to Replace the Push Roller
6.2.3 How to Replace the Push Roller Arm
6.2.4 How to Replace the Cam Sensor Board
6.2.5 How to Replace the Pen Block (without Auto Registration Sensor)
6.2.6 How to Replace the Pen Block (with Auto Registration Sensor)
6.2.7 How to Replace the Push Roller Sensor
6.2.8 How to Replace the Y-relay Board
6.2.9 How to Replace the Cutting Mat
6.2.10 How to Replace the Control Panel Relay Board, LCD Assembly and Membrane Switch Panel
6.2.11 How to Replace the Y-belt
6.2.12 How to Replace the Y-motor (CE3000-60/120)
6.2.13 How to Replace the Y-motor (CE3000-40)
6.2.14 How to Replace the X-motor
6.2.15 How to Replace the Y-flexible Cable
6.2.16 How to Replace the Vacuum Fan
6.2.17 How to Replace the Main Board
6.2.18 How to Replace the Power Supply
6.2.19 How to Replace the Drive Roller

7. ELECTRICAL ADJUSTMENTS
7.1 DIP Switch Settings
7.2 List of Items Requiring Readjustment
7.3 Explanation of the Values of the Main Board Settings
7.4 Clearing the Non-Volatile RAM
7.5 Adjusting the Pen Force
7.6 Adjusting the Distance Accuracy
7.7 Inputting the Servo Gain
7.8 Setting the Auto-Registration Mark Sensor Option
7.9 Adjusting the Auto-Registration Mark Sensor Sensitivity
7.10 Adjusting the Offset of the Auto-Registration Mark Sensor
7.11 Updating the System Firmware
7.12 Adjusting the Output Voltage of the Power Supply
7.13 Adjusting the Pen Exchange Y Direction Value (CE3000-120AP)
7.14 Adjusting the Pen Exchange Height Value (CE3000-120AP)
7.15 Adjusting the Spacing Between Pen 1 and Pen 2 (CE3000-120AP)

8 SERVICE MODES
8.1 Sensor Test Mode
8.2 Control Panel Membrane Switch Test Mode

9. TROUBLESHOOTING
9.1 The Plotter is Turned On But Doesn’t Operate
9.2 Media Loading Operations
9.3 Cutting Operations

10. PARTS LIST
10.1 Outer Casing
10.2 Main Frame
10.3 Base Assy for CE3000-120
10.4 Pen Block
10.5 Wiring Harness
10.6 Stand (CE3000-120/120AP standard, CE3000-60 optional)
10.7 Option Basket
10.8 Other Parts

11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.1 Block Diagrams
11.1.1 Block Diagram for CE3000-120
11.1.2 Block Diagram for CE3000-60
11.1.3 Block Diagram for CE3000-40
11.2 Circuit Diagrams
11.2.1 Main Board Top Section (PR270101A)
11.2.2 Main Board Connector Block Section (PR270101A)
11.2.3 Main Board CPU Block Section (PR270101A)
11.2.4 Main Board Motor Drive Section (PR270101A)
11.2.5 Main Board GRC 1507 Section (PR270101A)
11.2.6 Main Board Interface Section (PR270101A)
11.2.7 Main Board Memory Block Section (PR270101A)
11.2.8 Main Board USB Block Section (PR270101A)
11.2.9 Main Board Top Section (PR270102A)
11.2.10 Main Board Connector Block Section (PR270102A)
11.2.11 Main Board CPU Block Section (PR270102A)
11.2.12 Main Board 2-Phase Motor Drive Section (PR270102A)
11.2.13 Main Board Decoding Block Section (PR270102A)
11.2.14 Main Board Interface Section (PR270102A)
11.2.15 Main Board Memory Block Section (PR270102A)
11.2.16 Main Board USB Block Section (PR270102A)
11.2.17 Main Board Pen Drive Section (PR270102A)
11.2.18 Relay and Sensor Board Section
11.2.19 Control Panel Membrane Switch Panel Section
11.2.20 120-Relay Board Section
11.2.21 120-Pen Encoder Flexible Cable Section (FPC270101)

CE3000-40 CE3000-60 CE3000-120 CE3000-120AP ce2800-ssk ce3500 ce3000-40mk2 CE3000-60mk2 CE3000-120mk2 CE3000-40crp craft robo pro