Graphtec FC8000-60 FC8000-75 FC8000-100 FC8000-130 FC8000-160 Cutting plotter Service Manual and Parts List Manual

Service Manual and Parts List Manual Graphtec FC8000-60 FC8000-75 FC8000-100 FC8000-130 FC8000-160 Cutting plotter;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Graphtec.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Graphtec FC8000-60 FC8000-75 FC8000-100 FC8000-130 FC8000-160. You can find easily everything what do you need.
To see what contain, please read table of contents:

1. INTRODUCTION
1.1 Main Specifications
1.2 External Dimensions

2. PARTS NAMES and FUNCTIONS
2.1 Parts Names and Functions
2.2 Assembling
2.4 Replacing the Cross-Cutter Unit

3. OPERATIONS
3.1 Control Panel
3.2 Reading the Screen (LCD)

4. RECOMMENDED PARTS LIST

5. LIST OF TOOLS
5.1 Tools
5.2 Greasing And Gluing Points

6. DISASSEMBLY AND REASSEMBLY
6.1 Exterior Parts
6.1.1 How to Replace the Right Side Cover
6.1.2 How to Replace the Left Side Cover
6.1.3 How to Replace the Control Panel Assembly
6.1.4 How to Replace the Center Cover
6.1.5 How to Replace the Front Guide
6.1.6 How to Replace the Rear Guide
6.1.7 How to Replace the Rear Writing Panel
6.1.8 How to Replace the Front Writing Panel Assembly
6.2 Mechanical Parts
6.2.1 How to Replace the Rear Media Sensor
6.2.2 How to Replace the Front Media Sensor
6.2.3 How to Replace the Pinch Roller
6.2.4 How to Replace the Control Panel Board and the LCD
6.2.5 How to Replace the Pen Block
6.2.6 How to Replace the Y-belt
6.2.7 How to Replace the Pinch Roller Sensor
6.2.8 How to Replace the Y-relay Board
6.2.9 How to Replace the Cam Sensor
6.2.10 How to Replace the Y-motor
6.2.11 How to Replace the X-motor
6.2.12 How to Replace the Main Board
6.2.13 How to Replace the Vacuum Fan
6.2.14 How to Replace the Drive Roller
6.2.15 How to Replace the Cutting Mat
6.2.16 Home Dog Position
6.2.17 Cross Cutter Dog Position

7. ADJUSTMENTS
7.1 List of Items Requiring Readjustment
7.2 Mechanical Adjustments
7.2.1 Y-Belt Tension Adjustment
7.2.2 Y-Drive Belt Tension Adjustment
7.2.3 X-Drive Belt Tension Adjustment
7.2.4 Pinch Roller Pressure Adjustment
7.3 Electrical Adjustments
7.3.1 DIP Switch Settings
7.3.2 Explanation of the Values of the Main Board Settings
7.3.3 Clearing the Non-Volatile RAM
7.3.4 How to Enter the Adjustment Menu
7.3.7 Adjusting the Pen Force
7.3.8 Adjusting the Distance Accuracy
7.3.9 Adjusting the Registration Mark Sensor Sensitivity
7.3.10 Adjusting the Offset of the Auto-Registration Mark Sensor
7.3.11 Adjusting the Cross Cutter Home Position
7.3.12 Adjusting the Offset of the Light Pointer Position
7.3.13 Confirming the 2-Pen Model (2-pen model)
7.3.14 Adjusting the Pen Exchange Y Direction Value (2-pen model)
7.3.15 Adjusting the Spacing Between Pen 1 and Pen 2 (2-pen model)
7.4 Upgrading the System Firmware

8. TROUBLESHOOTING
8.1 The Plotter is Turned On But Doesn’t Operate
8.2 Media Loading Operations
8.3 Cutting Operations
8.4 Error Messages
8.4.1 Hardware Error Messages
8.4.2 Error Messages in GP-GL Command Mode
8.4.3 Error Messages in HP-GL Emulation Mode
8.4.4 Error Messages on ARMS
8.4.5 Other Error Messages
8.4.6 Warning Messages
8.5 Service mode
8.5.1 Sensor Test Mode & Panel Switch Test Mode
8.5.2 Printing the Setting of the Plotter
8.5.3 Printing the Test Pattern
8.5.4 Confirm the Cutting Data
8.5.5 Self Diagnostic Test

9. PARTS LIST
9.1 Outer Casing
9.2 Control Panel
9.3 Pen Block
9.4 Registration Mark Sensor Assy
9.5 Cross Cutter
9.6 Main Frame
9.7 Y Rail
9.8 Y Slider
9.9 Wiring Harness
9.10 Labels
9.11 Media Stocker, Stand
9.10 Basket
9.11 Other Parts

10. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
10.1 Block Diagrams
10.2 Circuit Diagrams
10.2.1 Main Board (CPU)
10.2.2 Main Board (CONNECTOR)
10.2.3 Main Board (MOTOR DRIVER)
10.2.4 Main Board (FPGA)
10.2.5 Main Board (I/F)
10.2.6 Main Board (MEMORY)
10.2.7 Main Board (Power)
10.2.8 LAN Board (Option)
10.2.9 Light Pointer
10.2.10 Pen Relay Board
10.2.11 Pinch Roller Sensor Board
10.2.12 RMS Board
10.2.13 Conrol Panel Board
10.2.14 Cam Sensor Board