Service Manual and Parts List Manual Mutoh MC-1300 Marathon Cutting Plotter;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Mutoh.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Mutoh MC-1300 Marathon Cutting Plotter photocopier. You can find easily everything what do you need.
To see what contain, please read table of contents:
1) SPECIFICATIONS
2) SYSTEM BLOCK DIAGRAM
3) INTERFACES
3.1. Serial interface RS-232C (standard)
3.1.1. RS232C pin configuration
3.1.2. Serial cable configuration
3.2. Centronics interface (standard)
3.2.1. Centronics interface Pin configuration
4) TROUBLESHOOTING
4.1. Recoverable errors
4.2. Unrecoverable errors
4.3. Problem symptoms and suggested actions
4.3.1. Processor errors
4.3.2. X-Y Servo errors
4.3.3. Cutting head errors
4.3.4. Other errors
4.4. Problem isolation
4.5. Rollfeed Errors
5) SPECIALISED DIAGNOSTICS
5.1. Diagnostics overview
5.2. Diagnostics mode :
5.2.1. Diagnostics 1 :
5.2.2. Diagnostics 2 :
5.2.3. Diagnostics 3 :
5.2.4. Diagnostics 4
5.2.5. Diagnostics 5
5.2.6. Diagnostics 6
5.2.7. Adjust. 7
5.2.8. Adjust. 8
5.2.9. Adjust. 9
5.2.10. Adjust. 10
6) PARTS REPLACEMENT AND ADJUSTMENTS
6.1. Maintenance access table for parts replacement
6.2. Mechanical parts
6.2.1. Cover left : removal and installation
6.2.2. Cover right : removal and installation
6.2.3. Transparent cover assy : removal and installation
6.2.4. PCB box : open and close
6.2.5. Y-rail cover : removal and installation
6.2.6. Grid cover : removal and installation
6.2.7. Cutting head : removal and installation
6.2.8. Grid rollers : removal and installation
6.2.9. Y-drive belt (long) : removal and installation
6.2.10. Pressure roller pressure adjustment
6.3. Electrical parts
6.3.1. Main PC board : removal and installation
6.3.2. EEPROM initialisation and replacement
6.3.3. Power supply board : removal and installation
6.3.4. Terminal board : removal and installation
6.3.5. Keyboard : removal and installation
6.3.6. X-motor and drive belt : removal and installation
6.3.7. Y-motor and drive belt : removal and installation
6.3.8. Head flex cable : removal and installation
6.3.9. Paper sensors : removal and installation
6.3.10. Transparent cover sensor : removal and installation
6.3.11. Pressure roller UP/DOWN sensor : removal and installation
6.3.12. Fan motors : removal and installation
6.3.13. Stocker home position sensor : removal and installation
6.3.14. Stocker motor : removal and installation
6.4. Rollfeed Parts
6.4.1. Remarks
6.4.2. Removing the Gear Cover
6.4.3. Removing the PCB cover
6.4.4. Replacing the gear motor assembly
6.4.5. Replacing the rollfeed PCB
6.4.6. Replacing a photo sensor in the front- or rear guidebar
6.4.7. Replacing a photo sensor in the front- or rear gear cover
7) JIG TOOL LIST
7.1. Jig tool list
7.2. Special glue
8) PLOTTERBODY AND ROLLFEED
9) PARTS LIST PLOTTERBODY
9.1. Platen and alignment (MY-23342)
9.2. Right cover and keyboard assy (MY-23539)
9.3. Cover left assy (MY-23540)
9.4. Transparent cover assy (MY-23306)
9.5. Stocker assy (MY-32244)
9.6. PCB box (MY-23001)
9.7. Penhead flex cable assy (MY-23571)
9.8. Pressure roller UP/DOWN assy (MY-23024/MY-23029)
9.9. X-motor assy (EY-10001)
9.10. X-rail assy (MY-2316-10400)
9.12. Y-rail assy (MY-2316-10401 and MY-23313)
9.13. Y-axis drive belt assy (MY-23350)
9.14. Y-drive pulley assy and mounting bracket (MY-47657)
9.15. Y-axis return pulley assy (MY-23075)
9.16. Pressure roller assy (MY-10402/10403)
9.17. End plates (MY-23010)
9.18. Penhead parts (MY-23864)
9.19. Stocker base assy (MY-23013)
10) PART LIST ROLLFEED SYSTEM
Mutoh MC1300 Marathon Cutting Plotter