Ricoh Aficio SP1200/SP1210N (product code M087 M088) Service Manual and Parts List Manual

This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Ricoh.
You can print, zoom or read any diagram, picture or page from this manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Ricoh Aficio SP1200/SP1210N (product code M087 M088) Service Manual and Parts List Manual.
To see what contain, please read table of contents:

Content for Service Manual:
Regulation
Safety Information
Acronyms and Technical Terms

1. PRODUCT INFORMATION
Specifications
Overview
Part names
Cross-section Drawing

2. INSTALLATION
Installation Requirements
Operating Environment
Power Supply

3. PREVENTIVE MAINTENANCE
Periodical Replacement Parts

4. REPLACEMENT AND ADJUSTMENT
Safety Precautions
Screw Torque List
Harness Routing
Fuser Unit
FG Harness
Main Frame R ASSY
Toner LED PCB ASSY / PS PCB Unit / Main PCB ASSY/Registration Front Sensor PCB ASSY /
Registration Rear Sensor PCB ASSY
Panel PCB ASSY / Toner Sensor PCB Unit ASSY / New Toner Sensor Harness ASSY
High-Voltage PS PCB / Registration Solenoid / T1 Solenoid
Disassembly Flow
Disassemble Procedure
Paper Tray Unit / Separation Pad Assy
Front Cover Assy
SW Key
Back Cover
Outer Chute Assy
Fuser Cover Assy
Eject Actuator / Eject Actuator Spring
Eject Roller Assy 1 / Bush C / Bush R / Bush L
Inner Chute Assy
Fuser Unit
Side Cover R Assy
Corner Cover
Side Cover L Assy
Roller Holder Assy
Main Shield Cover Plate
Main PCB Assy
Top Cover Assy
Paper Stack Lever
Support Flap 1 / Support Flap 2
Eject Roller Assy 2 / Bush R / Bush L
SW Supporter
Panel PCB Assy
High-Voltage PS PCB Assy
New Toner Sensor Harness Assy
Filter Assy
Laser Unit
Fan Motor 60 Unit
Cover Sensor Harness Assy
Toner LED PCB Assy
PS PCB Unit
LV Shield Plate 2
Registration Front Sensor PCB Assy
Registration Rear Sensor PCB Assy
Drive Sub Assy
Dev Joint / Dev Gear Joint 53R / Registration Pendulum Gear Spring
Toner Sensor PCB Unit Assy
Registration Solenoid
T1 Solenoid
Main Shield Plate / Eject Sensor PCB Assy
Rubber Foot
Main Frame L Assy
Adjustments and Updating of Settings, Required After Parts Replacement
If You Replace the Main PCB
If You Replace The Laser Unit
How to Select the Port Number

5. SERVICE MAINTENANCE
Control Panel
List of Service Support Functions
User Mode
Service Mode
Other Service Functions
Resetting the drum counter
Initializing the developing bias

6. TROUBLESHOOTING
Introduction
Precautions
Initial Check
Distinguish Error Cause
LED Indication
Message indication
Error Cause and Remedy
Paper Feeding Problems
No Feeding
Double Feeding
Paper Jam
Dirt on Paper
Wrinkles or Creases
Waves in the Paper / Folds in the Paper at the Eject Roller 2
Curl in the Paper
Image Defect Troubleshooting
Image Defect Examples
Diameter of Rollers
Troubleshooting Image Defect
Software Setting Problems
Network Problems
Others Problems
The Machine Is Not Turned On, or the LED Indication Does Not Appear
The fan does not work
Pickup Function of Paper Tray Does Not Work
A New Toner Cannot Be Detected

7. ENERGY SAVING
Energy Save
Sleep Modes
Paper Save
Effectiveness of Combine Function
INDEX

________________________

Content for Parts List Manual:
1. Exterior (M087/M088)
2. Paper Feed Section (M087/M088)
3. Paper Tray (M087/M088)
4. Laser Unit (M087/M088)
5. Fusing Unit (M087/M088)
6. Frame Section (M087/M088)
7. Electrical Section (M087/M088)
8. LV Power Supply (M087/M088)
9. HV Power Supply (M087/M088)
10. AC Cord (M087/M088)
11. Accessories (M087/M088)
Parts Index