Ricoh Aficio SP3500N/SP3510DN Service Manual, product code M116 M117

This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Ricoh.
You can print, zoom or read any diagram, picture or page from this manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Ricoh Aficio SP3500N/SP3510DN, product code M116 M117 Service Manual.
Table of contents:

1. PRODUCT INFORMATION
1.1 SPECIFICATIONS
1.2 MACHINE OVERVIEW
1.2.1 COMPONENT LAYOUT
1.2.2 PAPER PATH
1.2.3 DRIVE LAYOUT
1.3 MACHINE CONFIGURATION

2. INSTALLATION
2.1 INSTALLATION REQUIREMENTS
2.1.1 ENVIRONMENT
2.1.2 MACHINE LEVEL
2.1.3 MACHINE SPACE REQUIREMENT
2.1.4 POWER REQUIREMENTS
2.1.5 INSTALLATION PROCEDURE

3. PREVENTIVE MAINTENANCE
3.1 PM INTERVALS
3.1.1 PM PARTS
3.1.2 YIELD COUNTER
Counter Reset

4. REPLACEMENT AND ADJUSTMENT
4.1 BEFORE YOU START
4.2 SPECIAL TOOLS
4.3 EXTERIOR COVERS
4.3.1 FRONT COVER
4.3.2 LEFT COVER
4.3.3 REAR COVER
4.3.4 RIGHT COVER
4.3.5 TOP COVER
When installing the top cover
4.3.6 OPERATION PANEL
4.4 LASER UNIT
4.4.1 CAUTION DECAL LOCATIONS
4.4.2 LASER UNIT
4.4.3 POLYGON MIRROR MOTOR
4.5 PAPER FEED AND EXIT
4.5.1 PAPER FEED ROLLER
After installing a new paper feed roller
4.5.2 FRICTION PAD
4.5.3 PAPER END SENSOR
4.5.4 BY-PASS FEED ROLLER
4.5.5 BY-PASS FEED ROLLER FRICTION PAD
4.5.6 BY-PASS FEED SENSOR
4.5.7 PAPER FEED CLUTCH
4.5.8 RELAY CLUTCH
4.5.9 REGISTRATION CLUTCH
4.5.10 TONER END SENSOR
4.5.11 PAPER EXIT SENSOR
4.5.12 RELAY SENSOR
4.5.13 INVERTER SENSOR
4.5.14 REGISTRATION ROLLER AND SENSOR
4.6 PAPER TRANSFER
4.6.1 TRANSFER ROLLER
After installing a new transfer roller
4.7 FUSING
4.7.1 FUSING UNIT
Reinstallation
After installing a new fusing unit
4.7.2 THERMOSTAT
4.7.3 THERMISTOR
4.7.4 FUSING LAMP
When reinstall the fusing lamp
4.7.5 HOT ROLLER
4.7.6 PRESSURE ROLLER
4.7.7 HOT ROLLER STRIPPER PAWLS
4.8 MOTORS
4.8.1 MAIN MOTOR
4.8.2 DUPLEX MOTOR (FOR M117)
4.9 ELECTRICAL COMPONENTS
4.9.1 LAYOUT OF PC BOARDS
ECB (Engine Controller Board)
EEPROM
Controller Board
4.9.2 PSU
4.9.3 CHARGE TERMINAL CASE
4.10 OTHERS
4.10.1 COOLING FAN
4.10.2 QUENCHING LAMP
4.11 IMAGE ADJUSTMENT
4.11.1 REGISTRATION ADJUSTMENT
User Adjustment
Service Adjustment

5. SYSTEM MAINTENANCE REFERENCE
5.1 SERVICE PROGRAM MODE
5.1.1 OVERVIEW
5.1.2 ENTERING ENGINE MAINTENANCE MODE
5.1.3 SERVICE MODE MENU
Selecting an Item
Going into the Next Level/ Returning to the Previous Level
Exiting the Service Mode Menu
Menu List
5.2 CONFIGURATION AND MAINTENANCE PAGE
5.2.1 OVERVIEW
To Print the Configuration Page/ Maintenance Page
Other Types of Reports
Total Counter
5.3 FIRMWARE UPDATING
5.3.1 CHECKING THE MACHINE FIRMWARE VERSION
5.3.2 UPDATING THE CONTROLLER FIRMWARE
Procedure
5.3.3 UPDATING THE ENGINE FIRMWARE
Procedure
5.3.4 UPDATING THE BOOT LOADER FIRMWARE
5.3.5 UPDATING FAILURE
5.3.6 FW UPDATE TOOL MESSAGES
FW Update Tool Messages: Information
FW Update Tool Messages: Error

6. TROUBLESHOOTING
6.1 SERVICE CALL CONDITIONS
6.1.1 SUMMARY
Fusing related SCs
6.1.2 ENGINE SC
SC 2xx (Laser Optics Error)
SC 4xx (Image Transfer and Transfer Error)
SC 5xx (Motor and Fusing Error)
SC 6xx (Communication and Other Error)
6.2 IMAGE PROBLEMS
6.2.1 OVERVIEW
6.2.2 TEST PAGE PRINTING
Test Page Print Procedure
6.2.3 TEST PATTERN PRINTING
Test Pattern Print Procedure
6.2.4 DARK LINES IN HALFTONE AREAS AT 75MM INTERVALS
6.3 JAM
6.3.1 JAM SENSOR LAYOUT
Paper Jam
6.3.2 JAM MESSAGE LIST
Paper Jam

7. ENERGY SAVER
7.1 ENERGY SAVER MODES
7.1.1 TIMER SETTINGS
7.1.2 RETURN TO STAND-BY MODE
7.1.3 RECOMMENDATION
7.2 PAPER SAVE
7.2.1 EFFECTIVENESS OF DUPLEX/COMBINE FUNCTION
1. Duplex:
2. Combine mode:
3. Duplex + Combine:
Total counter