Service Manual and Parts List Manual Roland SolJet PROII V SC-545EX;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland Inkjet Printer/Cutter.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland SolJet PROII V SC-545EX. You can find easily everything what do you need.
To see what contain, please read table of contents:
1) Structure & Spare Parts
1-1 COVERS
1-2 FRAME
1-3 HEAD CARRIAGE
1-4 DRIVE UNIT
1-5 CHASSIS
1-6 PINCH ROLLER
1-7 STAY ROLL
1-8 TOOL CARRIAGE
1-9 WIPER SYATEM
1-10 PUMP SYSTEM
1-11 INK SYSTEM
1-12 BASE FRAME
1-13 ACCESSORIES & STAND
1-14 TUC-1 CONTROLLER
1-15 TUC-1 OTHERS
1-16 TUC-1 ACCESSORIES
1-17 TU-550
2) Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 HEAD / SERVO BOARD
2-4 SUB BOARD
2-5 TUC-1
2-6 HEATER BOARD
2-7 MAINTENANCE PARTS LIST
3) Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 WIPER REPLACEMENT
3-3 CAP TOP REPLACEMENT
3-4 TOOL CARRIAGE REPLACEMENT
3-5 CARRIAGE MOTOR REPLACEMENT
3-6 PUMP REPLACEMENT
3-7 INK TUBE REPLACEMENT
3-8 BOARDS REPLACEMENT
3-9 BATTERY REPLACEMENT
3-10 CARRIAGE WIRE REPLACEMENT
3-11 ENCODER SCALE REPLACEMENT
3-12 PINCH ROLLER REPLACEMENT
3-13 CUTTER PROTECTION REPLACEMENT
4) Adjustment
4-1 SPECIAL TOOLS
4-2 SERVICE MODE
4-3 HOW TO UPGRADE FIRMWARE
4-4 HEAD ALIGNMENT
4-5 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
4-6 LINEAR ENCODER SETUP
4-7 CAP HEIGHT ADJUSTMENT
4-8 CROP MARK SENSOR ADJUSTMENT
4-9 TOOL/CROP MARK SENSOR POSITION ADJUSTMENT
4-10 PRINT/CUT POSITION ADJUSTMENT
4-11 CALIBRATION (FEEDING DIRECTION)
4-12 TOOL HEIGHT ADJUSTMENT
4-13 TOOL PRESSURE ADJUSTMENT
4-14 CARRIAGE WIRE TENSION ADJUSTMENT
4-15 NETWORK BOARD INITIALIZE
4-16 OPERATION OF THE HEATER CONTROLLER
4-17 SETTING THE PARAMETER OF THE HEATER CONTROLLER
5) Supplemental Information
5-1 SENSOR MAP
6) Troubleshooting
6-1 WHITE FINE LINES / BANDING / MISSING DOT / SCRATCHY PRINTING / BLURRED PRINTING
6-2 IT DOESN’T PRINT AT ALL
6-3 INK DROPS ON MEDIA
6-4 SHIFTING IN PRINTING
6-5 VERTICAL BANDING
6-6 PRINT DOES NOT MATCH WITH CUT
6-7 STITCH CUT
6-8 START AND END POINTS DO NOT MATCH
6-9 DISTORTED FIGURE
6-10 MEDIA SHIFTING
6-11 MOTOR ERROR
6-12 ERROR MESSAGE/SERVICE CALL
6-13 HEATER TEMPERATURE FAILS TO REACH THE PRESET VALUE
6-14 RESULTS OF PRINTING ARE COARSE
6-15 ERROR MESSAGE (HEATER CONTROLLER)
7) Service Activities
7-1 INSTALLATION CHECK LIST
7-2 MAINTENANCE CHECK LIST
7-3 SPECIFICATION
Roland SolJet PROII V SC-545EX SJPROIIV SC545EX SJ PROII V SC 545EX PROII V 545 EX
About Roland SolJet PROII V SC-545EX and Documentation
This page provides technical documentation for the Roland SolJet PROII V SC-545EX and used by service technicians and maintenance professionals.
The parts list manual typically includes troubleshooting procedures, adjustment instructions, service mode information, internal component layouts and maintenance guidelines required for proper repair and servicing.
These documents are commonly used in professional repair environments where accurate technical reference and correct service procedures are required.