Xerox AltaLink C8170F Service Manual and Parts List Manual

Service Manual and Parts List Manual Xerox AltaLink C8170F
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Xerox.
You can print, zoom or read any diagram, picture or page from this manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Xerox AltaLink C8170F Service Manual and Parts List Manual.
Table of contents:

1. SERVICE CALL PROCEDURES
SCP 1 Initial Actions
SCP 2 Call Actions
SCP 3 Fault Analysis
SCP 4 Subsystem Maintenance
SCP 5 Final Actions
SCP 6 No longer required

2. STATUS INDICATOR RAPs

3. IMAGE QUALITY
Image Quality RAPs
IQ1 IOT Image Quality Entry RAP
IQ2 IIT Image Quality Entry RAP
IQ3 1mm Lines RAP
IQ4 Image Shift in Process Direction RAP
IQ5 White Lines RAP
IQ6 SLED Transfer Cycle Lines RAP
IQ7 IN-OUT Density Difference RAP
IQ8 Video Data/Crosstalk RAP
IQ9 Image Shift in Inboard-to Outboard Direction RAP
IQ10 Edge-less Image RAP
IQ11 Contamination Lines RAP
IQ12 Chip/Half Chip Blanks RAP
IQ13 SLED Transfer Failure RAP
IQ14 Tapes Not Peeled RAP
IQ15 Charging Roll Pitch White Lines (type 1)
IQ16 Charging Roll Pitch White Lines (type 2)
IQ17 Photoreceptor Pitch Color Lines
IQ18 Background on Gloss RAP
IQ19 Toner Empty Detection Color Lines RAP
IQ20 Toner Droplet Contamination RAP
IQ21 Smear on Heavyweight RAP
IQ22 Rough Black RAP
IQ23 Moist Paper Transfer Failure RAP
IQ24 Toner Contamination at Lead/Trail Edge RAP
IQ25 Trail Edge Transfer Failure RAP
IQ26 Color Lines RAP
IQ27 Transfer Blank Areas (Partially Moist Paper) RAP
IQ28 Nip Marks RAP
IQ29 Moisture RAP
IQ30 Low Image Density RAP
IQ31 Wrinkled Image RAP
IQ32 IOT Background RAP
IQ33 Color-to-Color Misregistration RAP
IQ34 Skew/Misregistration/Magnification RAP
IQ35 Process Direction Bands, Streaks, and Smears RAP
IQ36 Unfused Copy/Toner Offset RAP
IQ37 Repeating Bands, Streaks, Spots, and Smears RAP
IQ38 Spots RAP
IQ39 Missing Colors RAP
IQ40 Background on Coated Paper
IQ41 Multi Color Transfer Failure
IQ42 Lines on Coated Paper (EXIT)
IQ43 Caterpillar Mark (Transfer)
IQ44 White Stripes Due to Trimmer Jam (DEV)
IQ45 Heat Haze/Mock Heat Haze
IQ46 Poor Reproducibility of Fine Lines (IOT Image Quality)
IQ47 Outboard Deletion in All Colors
IQ48 MWS (Side 2) (Micro White Spots)
IQ49 Moist Paper Wrinkles (Fusing Unit)
IQ50 White Streaks in Process Direction/Dropping Density (XERO/CLN)
IQ51 Background (IPS)
IQ53 Highlight Density Reproduction (NVM Darken +3) (IPS)
IQ54 Highlight Density Reproduction (NVM Lighten +3) (IPS)
IQ56 CVT Streaks (IPS)
IQ57 Copy: Gradation Jump in Text & Photo (IPS)
IQ58 Scan: Smeared Text, JPEG Mosquito Noise (IPS)
IQ59 Moire In Text Mode (Fine) BW Scan/Fax For 133 lpi Originals (IPS)
IQ60 Copy: Bleed on 2 Sided Document (IPS)
IQ61 Copy: Platen Background (IPS)
IQ66 Unevenness Correction Within Image Area (IOT Image Quality)
IQ67 Ghost Image
IQ68 Toner Color Streaks
IQ69 Heavyweight Paper Image Blurring
IQ70 Scale-Like and Circular Stamping Marks Defect
IQ71 3mm Pitch Streak
IQ72 Paper Wrinkle Due to Misaligned Fuser Transport Rolls
Image Quality Specifications
IQS 1 Test Pattern Usage (dC612)
IQS 2 IIT Image Quality Specifications
IQS 3 Things to Note for Image Quality Restrictions
IQS 4 Fusing

4. REPAIRS ADJUSTMENTS
REPs Chain 1 – Electrical Components
REP 1.1 BTR HVPS PWB
REP 1.2 Fuser Heater Power Supply
REP 1.3 GFI Chassis Assembly
REP 1.4 Motor Drive PWB
REP 1.5 AC Drive PWB
REP 1.6 LVPS
REP 1.7 Developer Bias HVPS PWB
REP 1.8 Main Power Switch
REP 1.9 BCR HVPS PWB
REPs Chain 2 – User Interface
REP 2.1 UI Assembly
REPs Chain 3 – Machine Run Control
REP 3.1 Controller PWB Assembly
REP 3.2 Relay PWB
REP 3.3 Back Plane PWB
REP 3.4 Halftone PWB
REP 3.5 HDD
REP 3.6 MCU PWB
REPs Chain 5 – DADF 250
REP 5.1 DADF 250
REP 5.2 DADF 250 Left Lower Cover
REP 5.3 DADF 250 Front Cover
REP 5.4 NOT USED
REP 5.5 DADF 250 Rear Cover
REP 5.6 NOT USED
REP 5.7 DADF 250 IIT-DADF Cable
REP 5.8 DADF 250 PWB
REP 5.9 DADF 250 Left Counter Balance
REP 5.10 DADF 250 Right Counter Balance
REP 5.11 DADF 250 DCDC PWB
REP 5.12 DADF 250 CIS
REP 5.13 NOT USED
REP 5.14 DADF 250 Feed Motor and Belts
REP 5.15 NOT USED
REP 5.16 DADF 250 Tray Motor Assembly
REP 5.17 DADF 250 Oil Damper and Document Set LED
REP 5.18 NOT USED
REP 5.19 DADF 250 Tray APS Sensor 1/Tray APS Sensor 2/Tray APS Sensor 3/Tray APS Sensor 4/Bottom Sensor
REP 5.20 DADF 250 Document Set Sensor
REP 5.21 DADF 250 Feeder Cover Assembly
REP 5.22 DADF 250 Feeder Cover Interlock Switch
REP 5.23 DADF 250 Left Cover Assembly
REP 5.24 DADF 250 L/H Cover Interlock Sensor and Actuator
REP 5.25 DADF 250 Feed In Sensor 1/DADF Feed In Sensor 2
REP 5.26 DADF 250 Level Sensor
REP 5.27 DADF 250 Rear Latch Assembly
REP 5.28 DADF 250 Nudger Housing Assembly
REP 5.29 DADF 250 Nudger Solenoid Assembly
REP 5.30 NOT USED
REP 5.31 DADF 250 Out Sensor
REP 5.32 DADF 250 Registration Sensor
REP 5.33 DADF 250 Pre Registration Sensor/APS Sensor 1/APS Sensor 2/APS Sensor 3
REP 5.34 DADF 250 Feed Out Sensor/Exit Sensor
REP 5.35 DADF 250 Skew Detect Sensor
REP 5.36 DADF 250 Lead Registration Sensor
REP 5.37 DADF 250 Pre Registration Motor
REP 5.38 DADF 250 Takeaway Clutch Assembly
REP 5.39 DADF 250 Exit Motor and Belt
REP 5.40 DADF 250 Platen Motor and Belt
REP 5.41 DADF 250 Registration Motor and Belt
REP 5.42 DADF 250 Lower Chute Assembly
REP 5.43 DADF 250 Friction Clutch
REP 5.44 DADF 250 Retard Roll and Spring
REP 5.45 DADF 250 Exit Eliminator
REP 5.46 NOT USED
REP 5.47 DADF 250 Pre Registration In Chute Assembly
REP 5.48 DADF 250 Registration Out Chute Assembly
REP 5.49 DADF 250 Platen High Roll Assembly
REP 5.50 DADF 250 Exit 1 and Platen Belts
REP 5.51 DADF 250 Exit Lower Chute Assembly
REP 5.52 NOT USED
REP 5.53 DADF 250 Out Chute Assembly
REP 5.54 DADF 250 Feed Roll
REP 5.55 DADF 250 Document Tray
REP 5.56 DADF 250 PWB Wire Harness and Harness Guide
REPs Chain 5 – DADF 130
REP 5.60 DADF 130
REP 5.61 DADF 130 Platen Cushion
REP 5.62 DADF 130 Front Cover
REP 5.63 DADF 130 Rear Cover
REP 5.64 DADF 130 Feeder Assembly
REP 5.65 DADF 130 PWB
REP 5.66 DADF 130 DC/DC PWB
REP 5.67 DADF 130 Left Counter Balance
REP 5.68 DADF 130 Right Counter Balance
REP 5.69 DADF 130 Document Tray
REP 5.70 DADF 130 Top Cover
REP 5.71 DADF 130 Wire Harness and Harness Guide
REP 5.72 DADF 130 Registration Motor
REP 5.73 DADF 130 Feed Motor
REP 5.74 DADF 130 Pre Registration Motor
REP 5.75 DADF 130 Registration Chute
REP 5.76 DADF 130 Retard Chute
REP 5.77 DADF 130 Out Chute
REP 5.78 DADF 130 CIS
REP 5.79 DADF 130 Sensor Bracket
REP 5.80 DADF 130 Nudger Roll and Feed Roll
REP 5.81 DADF 130 Retard Roll
REP 5.82 DADF 130 Feed In/Feed Out Sensor
REP 5.83 DADF 130 Exit Sensor
REP 5.84 DADF 130 APS Sensor 1/APS Sensor 2/APS Sensor 3
REP 5.85 DADF 130 Registration Sensor/Out Sensor/Pre-Registration Sensor
REP 5.86 DADF 130 Document Set Sensor
REP 5.87 DADF 130 Document Set Actuator
REP 5.88 DADF 130 Feed/Nudger Roll Assembly
REP 5.89 DADF 130 Tray APS Sensor 1/APS Sensor 2/APS Sensor 3
REP 5.90 DADF 130 Document Tray Size Sensor 1 and 2
REPs Chain 10 – Fuser/Post-Fuser Transport
REP 10.1 Retract Motor Assembly
REP 10.2 Fuser
REP 10.3 Fuser Heater Coil
REP 10.4 Exit 1 Transport Assembly
REP 10.5 Exit 1 OCT Motor
REP 10.6 Exit 1 OCT Home Position Sensor
REP 10.7 Exit 1 Drive Gear
REP 10.8 Exit 2 Transport Assembly
REP 10.9 Exit 2 Drive Assembly
REP 10.10 Exit 1 Gate Solenoid
REP 10.11 Exit 2 OCT Home Position Sensor
REP 10.12 Offset Gear
REPs Chain 28 Covers
REP 28.1 Front Left Cover
REP 28.2 SWEA Cover 2
REPs Chain 40 – Drive
REP 40.1 Main Drive Assembly
REP 40.2 Fuser Drive Assembly
REP 40.3 Temp/Humidity Sensor (No 1 external)
REP 40.4 Duct Assembly (Front Right Marking Fan)
REP 40.5 Toner Cartridge Cooling Fan Assembly
REP 40.6 Front/Left Marking Fan Assembly
REP 40.7 Rear Fuser Duct Assembly
REP 40.8 LVPS Fan Assembly
REP 40.9 IHPS Intake Duct Assembly
REP 40.10 Toner Cartridge Exhaust Fan Assembly
REPs Chain 60 – IIT Common
REP 60.1 LPH Assembly (Y,M,C,K)
REP 60.2 FFC Cable Assembly
REPs Chain 60 – IIT (C8170)
REP 60.3 Scanner Module, CVT/Document Glass (High)
REP 60.4 Scanner Electrical Components (C8170)
REP 60.5 Scan Carriage Assembly (C8170)
REP 60.6 Side 2 Scan Assembly (C8170)
REP 60.7 Scanner Module, CVT/Document Glass (C8170)
REP 60.10 Not Used
REP 60.11 CCD Lens Cover (C8170)
REP 60.12 IIT Registration Sensor (C8170)
REP 60.13 Platen Angle Sensor (C8170)
REP 60.14 CCD Flexible Print Cable (C8170)
REP 60.15 IIT Lens Assembly (C8170)
REP 60.16 CCD Fan (C8170)
REP 60.17 Carriage Motor (C8170)
REP 60.18 Full Rate Carriage (C8170)
REP 60.19 Rear Carriage Cable (C8170)
REP 60.20 IIT Trans PWB (C8170)
REP 60.21 Exposure Lamp (C8170)
REP 60.22 Lamp PWB (C8170)
REP 60.23 Slide Chord (C8170)
REPs Chain 60 – IIT (C8130/35/45/55)
REP 60.25 Document Glass
REP 60.29 CCD Lens Assembly
REP 60.30 Front/Rear Carriage Cables
REP 60.31 Lamp Assembly
REP 60.32 LED Ribbon Cable
REP 60.33 Light Guide
REP 60.34 IIT Carriage Motor
REP 60.35 CCD Cont Video Ribbon Cable
REP 60.36 IIT Trans PWB (C8130/35/45/55)
REPs Chain 70- Paper Supply
REP 70.1 Tray 1 and Tray 2 Paper Size Sensor
REP 70.2 Pivot
REP 70.3 Bypass Tray
REP 70.4 Bypass Tray Paper Size Sensor Assembly
REP 70.5 2TM Tray 3/4 Paper Size Sensor Assembly
REP 70.6 TTM Tray 3/4 Paper Size Sensor Assembly
REPs Chain 80 – Paper Transportation
REP 80.1 Tray 1 Feedhead Assembly
REP 80.2 Tray 2 Feedhead Assembly
REP 80.3 Tray 1/2 Feed Roll Kit
REP 80.4 2TM Feedhead 1 Assembly
REP 80.5 2TM Feedhead 2 Assembly
REP 80.6 2TM Takeaway Roll Assembly (Upper)
REP 80.7 2TM Tray Chute Assembly
REP 80.8 2TM Takeaway Roll Assembly (Lower)
REP 80.9 2TM Takeaway Motor Assembly
REP 80.10 2TM Belt
REP 80.12 2TM Feed Roll Kit
REP 80.14 TTM Tray 3 Feedhead Assembly
REP 80.15 TTM Tray 4 Feedhead Assembly
REP 80.16 TTM Feed Roll Kit
REP 80.17 TTM Transport Roll Assembly
REP 80.19 Bypass Feedhead Assembly
REP 80.20 Bypass Tray Roll Kit
REP 80.21 Left Cover Assembly
REP 80.22 2nd BTR Roll Assembly
REP 80.23 2nd BTR Housing Assembly
REP 80.24 Duplex Inner Chute Assembly
REP 80.25 Lower Chute Assembly
REP 80.26 Registration Sensor
REP 80.27 Handle
REP 80.28 POB Jam Sensor
REP 80.29 Left Cover Interlock Switch Assembly
REP 80.30 Registration Transport Assembly
REP 80.31 Chute Assembly
REP 80.32 Takeaway Roll Assembly
REP 80.33 Registration Drive Assembly
REP 80.34 Drive Assembly (Takeaway Motor 2)
REPs Chain 90 – Xerographics
REP 90.1 Conductor Housing Assembly
REP 90.2 Plunger
REP 90.3 New Developer Assembly (Y,M,C,K)
REP 90.4 Toner Dispense Motor Assembly
REP 90.5 Toner CRUM Connector Assembly
REP 90.6 Dispenser Assembly
REP 90.7 Developer Replacement
REP 90.8 IBT Belt Assembly
REP 90.9 MOB/ADC Assembly
REP 90.10 Upper Conductor Housing Assembly
REP 90.11 Drum Assembly
REP 90.12 Gear Housing Assembly
REP 90.13 Drive Shaft
REP 90.14 Agitator Motor Assembly
REP 90.15 Joint Pipe Assembly
REP 90.16 Housing Assembly
REP 90.17 Sleeve Bearing
REP 90.18 Waste Toner Cartridge Sensors
ADJs Chain 2 – User Interface
ADJ 2.1 Panel (UI) Diagnostic Tests
ADJs Chain 5 – DADF 250/130
ADJ 5.1 DADF Skew Adjustment
ADJ 5.2 DADF Side Registration Manual Adjustment
ADJ 5.4 DADF Lead Edge Registration Manual Adjustment
ADJ 5.5 DADF Registration Automatic Adjustment (dC608)
ADJ 5.6 Side 1 to Side 2 Color Matching
ADJs Chain 60 – IIT
ADJ 60.1 Full/Half Rate Carriage Position Adjustment
ADJ 60.2 IIT Lead Edge Registration Manual Adjustment
ADJ 60.3 IIT Side Registration Manual Adjustment
ADJ 60.4 Optical Axis Calibration
ADJ 60.5 IIT Calibration (dC945)
ADJ 60.7 Document Glass Registration Automatic Adjustment (dC609)
ADJs Chain 90 – Electrical/Xerographic
ADJ 90.1 IOT Lead Edge/Side Edge Registration (dC126)
ADJ 90.2 Edge Erase Adjustment
ADJ 90.3 ProCon On/Off Print Check (dC937)
ADJ 90.5 Thin Line Correction Mode Adjustment
ADJ 90.6 LPH Exposure Amount Fine Adjustment
ADJ 90.7 ATC Sensor Setup (dC950)
ADJ 90.8 ATC Developer Setup (dC949)
ADJ 90.9 Color Registration Measurement Cycle (dC671)
ADJ 90.10 Color Registration Control Setup Cycle (dC675)
ADJ 90.11 Color Registration Control Sensor Check Cycle (dC673)
ADJ 90.12 Copy Color Balance Manual Adjustment (dC919)
ADJ 90.13 TRC Manual Adjustment (dC924)
ADJ 90.14 Tone Up/Tone Down (dC991)
ADJ 90.16 MAX Setup
ADJ 90.17 Paper Calibration (dC1215)
ADJ 90.18 Image Size Adjustment (dC603)

5. PARTS LIST
Parts Lists
PL 1 – Standby Power
PL 1.05 Electrical – Rear (1 of 3)
PL 1.10 Electrical – Rear (2 of 3)
PL 1.15 Electrical – Rear (3 of 3)
PL 1.20 Electrical – Front/Right
PL 1.25 Wire Harness
PL 2 – User Interface
PL 2.05 User Interface (C8130/C8135/C8145/C8155)
PL 2.10 User Interface (C8170)
PL 3 – Machine Run Control
PL 3.05 Control Unit (ESS PWB)
PL 3.10 Video Contact Chassis Unit
PL 3.15 Video Contact Chassis Assembly
PL 5 – DADF (250)
PL 5.1 DADF Component (250) (C8170)
PL 5.2 DADF, DADF Cover (250) (C8170)
PL 5.3 DADF PWB (250) (C8170)
PL 5.4 DCDC PWB (250) (C8170)
PL 5.5 Document Tray, Tray Feed (250) (C8170)
PL 5.6 DADF Document Tray (250) (C8170)
PL 5.7 DADF Feeder Cover Unit (250) (C8170)
PL 5.8 DADF Feeder Cover Assembly (250) (C8170)
PL 5.9 Sensor Component (250) (C8170)
PL 5.10 Drive Component (250) (C8170)
PL 5.11 Lower Chute Assembly, Retard Roll (250) (C8170)
PL 5.12 Pre Regi. In Chute, Platen High Roll (250) (C8170)
PL 5.13 Exit Lower Chute, Out Chute Assembly (250) (C8170)
PL 5.14 DADF Nudger Housing Assembly (250) (C8170)
PL 5 – DADF (130)
PL 5.50 DADF Component (130) (C8130/C8135/C8145/C8155)
PL 5.51 DADF Cover (130) (C8130/C8135/C8145/C8155)
PL 5.52 DADF Top Cover, Document Tray (130) (C8130/C8135/C8145/C8155)
PL 5.53 DADF Base Frame Assembly (130) (C8130/C8135/C8145/C8155)
PL 5.54 Regi. / Retard Chute/ Invert Unit (130) (C8130/C8135/C8145/C8155)
PL 5.55 Top Cover (130) (C8130/C8135/C8145/C8155)
PL 5.56 Feeder / Nudger Roll Assembly (130) (C8130/C8135/C8145/C8155)
PL 5.57 DADF Document Tray (130) (C8130/C8135/C8145/C8155)
PL 5.58 DADF Drive (130) (C8130/C8135/C8145/C8155)
PL 10 – Copy Transportation and Fusing
PL 10.05 Fuser
PL 10.10 Exit 1 Transport Components
PL 10.15 Exit 2 Transport Components
PL 10.20 Face Up Tray Assembly
PL 10.25 Exit 2 Transport Assembly
PL 10.30 Face Up Chute Assembly
PL 20 – Fax
PL 20.10 Fax Module
PL 25 – Accessories
PL 25.10 Accessories
PL 26 – Consumables and Tools
PL 26.10 Consumables and Tools
PL 28 – Covers
PL 28.05 Covers (Front)
PL 28.10 Covers (Rear)
PL 28.15 Covers (C8130/C8135/C8145/C8155)
PL 28.20 Covers (C8170)
PL 28.25 Front Left Cover Compartment
PL 28.30 Workshelf
PL 40 – Main Drive Assembly
PL 40.05 Main Drive Assembly
PL 40.10 NOHAD (front)
PL 40.15 NOHAD (rear)
PL 60 – Imaging
PL 60.05 LPH Module
PL 60.10 Platen/IIT Cover (C8170)
PL 60.15 Platen Glass (C8170)
PL 60.20 CCD Lens (C8170)
PL 60.25 Carriage Cable/Motor (C8170)
PL 60.30 Full/Half Carriage (C8170)
PL 60.35 Platen/IIT Cover (C8130/C8135/C8145/C8155)
PL 60.40 Platen Glass (C8130/C8135/C8145/C8155)
PL 60.45 CCD Lens (C8130/C8135/C8145/C8155)
PL 60.50 Carriage Cable/Motor (C8130/C8135/C8145/C8155)
PL 60.55 Full/Half Carriage (C8130/C8135/C8145/C8155)
PL 70 – Paper Supply
PL 70.05 Tray 1 2 Assembly
PL 70.10 Tray 1 Assembly
PL 70.15 Tray 2 Assembly
PL 70.20 2TM Components (C8130/C8135)
PL 70.25 2TM Tray 3/4 Assembly (C8130/C8135)
PL 70.30 TTM Components
PL 70.35 TTM Covers and Tray 3/4 Assembly
PL 70.40 TTM Tray 3 Assembly
PL 70.45 TTM Tray 4 Assembly
PL 70.50 Bypass Tray Components
PL 70.55 Bypass Tray Assembly
PL 70.70 Envelope Tray
PL 80 – Paper Transport
PL 80.05 Tray 1 2 Feedhead Assembly
PL 80.10 Tray 1 Feedhead Assembly
PL 80.15 Tray 2 Feedhead Assembly
PL 80.20 2TM Left Cover Feedhead Assembly (C8130/C8135)
PL 80.25 2TM Takeaway Assembly (C8130/C8135)
PL 80.30 2TM Drive Assembly (C8130/C8135)
PL 80.35 2TM Tray 3 4 Feedhead Assembly (C8130/C8135)
PL 80.40 TTM Transport Assembly / Tray 3 4 Feedhead Assembly
PL 80.45 TTM Drive Assembly
PL 80.50 TTM Tray 3 Feedhead Assembly
PL 80.55 TTM Tray 4 Feedhead Assembly
PL 80.60 TTM Transport Assembly
PL 80.65 Left Cover Components
PL 80.70 Left Cover Transport Components
PL 80.75 Left Cover Transport Assembly
PL 80.80 Duplex Inner Chute Assembly
PL 80.85 Duplex Chute Assembly
PL 80.90 Registration Transport Assembly
PL 80.95 Registration Drive Assembly
PL 80.115 Bypass Tray Takeaway Assembly
PL 80.120 Bypass Tray Feedhead Assembly
PL 90 – Xerographics
PL 90.05 Developer Unit
PL 90.10 Toner Dispense
PL 90.15 Xerographic Components
PL 90.20 Xerographic Assembly (1 of 2)
PL 90.25 Xerographic Assembly (2 of 2)
PL 90.30 IBT Belt Unit Components
PL 90.35 IBT Belt Unit Assembly
PLCH – Common Hardware
Common Hardware

6. GENERAL PROCEDURES AND INFORMATION
Service Diagnostic Mode
Service Copy (Tools) Mode
dC104 System Usage Counters
dC108 Software Versions
dC120 Fault Counter
dC122 Fault History
dC126 Paper Registration
dC128 Fold Position Adjustment
dC131 NVM Read/Write
dC132 Serial Number Synchronize
dC135 HFSI Counters
dC140 Analog Monitor
dC301 NVM Initialization
dC304 LPH EEPROM Self test
dC305 Panel Diagnostics Test
dC312 Network Echo Tests
dC330 Component Control
dC361 NVM Save and Restore
dC363 EEPROM Backup and Restore
dC527 DADF Size Detection
dC603 Image Size Adjustment
dC608 Document Feeder Registration Automatic Adjustment
dC609 Document Glass Registration Automatic Adjustment
dC612 Print Test Pattern
dC671 Measurement Cycle
dC673 Registration Control Sensor Check
dC675 Registration Control Setup
dC710 No Paper Run
dC740 MSI Side Guide Adjustment
dC919 Color Balance Adjustment
dC924 TRC Manual Adjustment
dC931 Input / Output Manual Setup
dC937 ProCon On/Off Print
dC945 IIT Calibration
dC949 ATC Developer Setup
dC950 ATC Sensor
dC991 Tone Up/Tone Down
dC1215 Calibrate for Paper
GP 1 FAX PWB Internal Selftest
GP 2 Accessing Tools
GP 3 Controller Boot Sequence
GP 4 Power the System Off/On
GP 5 Image Quality Calibration
GP 6 Printing Configuration Reports
GP 7 Network Printing Simulation
GP 8 Speed Kit Enablement
GP 9 Installing System Software
GP 10 PWS Communication with the SBC
GP 11 Resetting the System Administrator Password
GP 12 Back Up and Restore Settings
GP 13 Cloning Network Configurations
GP 14 External Fax Line Test
GP 15 Electrical Power Requirements
GP 16 Service Plan Conversion
GP 17 How to Re-Enter Optional Feature Installation Keys
GP 18 Restoring the Device Address Book
GP 19 Environmental Data
GP 20 Reporting Billing Meter Resets
GP 21 First Print Out Time and Power On Time
GP 22 Foreign Device Interface Setup
GP 23 Intermittent or Noise Problem RAP
GP 24 How to turn off the Power Saver Functions
GP 25 Remote Control Panel
GP 28 Billing Impression Mode Verification
GP 29 Restoring Customer Mode
GP 30 Reloading NVM from the Tray 1 List
GP 31 Print/Copy Orientation Definitions
GP 32 How to Open and Close the Video Contact Chassis Unit
GP 33 Installation Space Requirements
GP 34 How to Enable HTTP
GP 35 How to Change Ethernet Speed
GP 36 How to Disable the Firewall of the PWS
GP 37 How to Configure the PWS to Ping a Device
GP 38 How to Set the IP Address of the PWS
Glossary of Terms, Acronyms and Abbreviations

7. WIRING DATA
7.1 Plug/Jack Locations
Plug/Jack Location List
Plug/Jack Location
7.2 Wiring Diagrams
Introduction
Wiring Diagram 1 ACH/ACN 100VAC (Low/Mid)
Wiring Diagram 2 ACH/ACN 100VAC (High) (2 Plugs)
Wiring Diagram 3 ACH/ACN 220-240VAC (Low/Mid/High)
Wiring Diagram 4 Not Used
Wiring Diagram 5 +24VDC (Low/Mid)
Wiring Diagram 6 +24VDC (High)
Wiring Diagram 7 +24VDC (1 of 2)
Wiring Diagram 8 +24VDC (2 of 2)
Wiring Diagram 9 +5VDC (Low/Mid) (1 of 2)
Wiring Diagram 10 +5VDC (Low/Mid) (2 of 2)
Wiring Diagram 11 +5VDC (High) (1 of 2)
Wiring Diagram 12 +5VDC (High) (2 of 2)
Wiring Diagram 13 +5VDC (1 of 2)
Wiring Diagram 14 +5VDC (2 of 2)
Wiring Diagram 15 +3.3VDC/+2.5VDC (1 of 2)
Wiring Diagram 16 +3.3VDC/+2.5VDC (2 of 2)
Wiring Diagram 17 DC COM (Low/Mid) (1 of 2)
Wiring Diagram 18 DC COM (Low/Mid) (2 of 2)
Wiring Diagram 19 DC COM (High) (1 of 2)
Wiring Diagram 20 DC COM (High) (2 of 2)
Wiring Diagram 21 DC COM (1 of 5)
Wiring Diagram 22 DC COM (2 of 5)
Wiring Diagram 23 DC COM (3 of 5)
Wiring Diagram 24 DC COM (4 of 5)
Wiring Diagram 25 DC COM (5 of 5)
Wiring Diagram 26 Tray +24VDC/+5VDC/+3.3VDC (2TM)
Wiring Diagram 27 Tray +24VDC/+5VDC/+3.3VDC (TTM)
Wiring Diagram 28 Tray DC COM (2TM)
Wiring Diagram 29 Tray DC COM (TTM)
Wiring Diagram 30 IIT +24VDC (Low/Mid)
Wiring Diagram 31 IIT +24VDC (High)
Wiring Diagram 32 IIT +24VDC/+11VDC/+10VDC/+5VDC/+1.9VDC (Low/Mid)
Wiring Diagram 33 IIT +24VDC/+11VDC/+10VDC/+5VDC/+1.9VDC (High)
Wiring Diagram 34 IIT Return (Low/Mid)
Wiring Diagram 35 IIT Return (High)
Wiring Diagram 36 DADF 130 +24VDC/+5VDC (1 of 2)
Wiring Diagram 37 DADF 130 +24VDC/+5VDC (2 of 2)
Wiring Diagram 38 DADF 130 Return (1 of 2)
Wiring Diagram 39 DADF 130 Return (2 of 2)
Wiring Diagram 40 DADF 250 +24VDC/+5VDC
Wiring Diagram 41 DADF 250 +5VDC
Wiring Diagram 42 DADF 250 +24VDC/+5VDC/+3.3VDC
Wiring Diagram 43 DADF 250 Return (1 of 2)
Wiring Diagram 44 DADF 250 Return (2 of 2)
7.3 Block Schematic Diagrams (BSDs)
Symbology
Chain 1 Standby Power
BSD 1.1 Main Power On 100VAC (Low/Mid)
BSD 1.2 Main Power On 100VAC (High) (2 Plugs)
BSD 1.3 Main Power On 220-240VAC (Low/Mid/High)
BSD 1.4 Machine Power Control (1 of 2)
BSD 1.5 Machine Power Control (2 of 2)
BSD 1.6 DC Power Generation +5V (Low/Mid)
BSD 1.7 DC Power Generation +24V (1 of 2) (Low/Mid)
BSD 1.8 DC Power Generation +24V (2 of 2) (Low/Mid)
BSD 1.9 DC Power Generation +5V (High)
BSD 1.10 DC Power Generation +24V (1 of 2) (High)
BSD 1.11 DC Power Generation +24V (2 of 2) (High)
BSD 1.12 Interlock Switching
BSD 1.13 Fuse Check
BSD 1.14 LVPS Cooling
BSD 1.15 PWB Locations (Low/Mid)
BSD 1.16 PWB Locations (High)
Chain 3 Machine Run Control
BSD 3.1 PWB Communications (Controller to Motor Drive PWB)
BSD 3.2 PWB Communications (Controller to UI)
BSD 3.3 PWB Communications (Controller to Finisher)
BSD 3.4 PWB Communications (Controller to HCF)
BSD 3.5 PWB Communications (Controller to Halftone/Back Plane)
BSD 3.6 PWB Communications (Controller to DADF PWB) (Low/Mid/High)
BSD 3.7 Electric Billing
BSD 3.8 Controller (SBC) PWB
BSD 3.9 PWB Communications (Controller to IIT Trans PWB)
Chain 5 DADF 250
BSD 5.1 DADF 250 Interlock and Document Set
BSD 5.2 DADF 250 Document Stacking
BSD 5.3 DADF 250 Document Size Sensing (Fast Scan)
BSD 5.4 DADF 250 Document Feeding
BSD 5.5 NOT USED
BSD 5.6 DADF 250 Document Size Sensing (Slow Scan)
BSD 5.7 DADF 250 Document Pre Registration and Skew Detect
BSD 5.8 DADF 250 Document Registration
BSD 5.9 DADF 250 Document Scan (Side 1)
BSD 5.10 DADF 250 Document Scan (Side 2) (1 Of 2)
BSD 5.11 DADF 250 Document Scan (Side 2) (2 Of 2)
BSD 5.12 DADF 250 Document Exit
BSD 5.13 DADF 250 Document Path and Drive Transmission
Chain 5 DADF 130
BSD 5.14 DADF 130 Interlock And Document Setting
BSD 5.15 DADF 130 Document Size Sensing
BSD 5.16 DADF 130 Document Feeding (1 of 2)
BSD 5.17 DADF 130 Document Feeding (2 of 2)
BSD 5.18 DADF 130 Pre Registration
BSD 5.19 DADF 130 Registration
BSD 5.20 DADF 130 Document Scan (1 of 2)
BSD 5.21 DADF 130 Document Scan (2 of 2)
BSD 5.22 DADF 130 Document Exit
BSD 5.23 DADF 130 Document Path and Drive Transmission
Chain 10 Print Transport and Fusing
BSD 10.1 Fusing Unit Drive
BSD 10.2 Pressure Roll Latch/Unlatch
BSD 10.3 Fusing Heat (1 of 2)
BSD 10.4 Fusing Heat (2 of 2)
BSD 10.5 Fusing
BSD 10.6 Fuser Detection
BSD 10.7 Exit 1 Paper Transport
BSD 10.8 Duplex Paper Transport
BSD 10.9 Exit 2 Paper Transport (1 of 2)
BSD 10.10 Exit 2 Paper Transport (2 of 2)
BSD 10.11 Face Up Paper Transport
Chain 34 Fax
BSD 34.1 Fax
Chain 40 Main Drives
BSD 40.1 K Drum/Developer and IBT Drive Control (Low/Mid/High)
BSD 40.2 YMC Drum and Developer Drive Control (Low/Mid)
BSD 40.3 YMC Drum Drive Control (High)
BSD 40.4 YMC Developer Drive Control (High)
Chain 60 Imaging
BSD 60.1 Platen Document Sensing (Low/Mid – C8130/35/45/55)
BSD 60.2 Platen Document Sensing (High – C8170)
BSD 60.3 Document Illumination (Low/Mid – C8130/35/45/55)
BSD 60.4 Document Illumination (High – C8170)
BSD 60.5 Carriage Control (Low/Mid – C8130/35/45/55)
BSD 60.6 Carriage Control (High – C8170)
BSD 60.7 Image Input (Low/Mid – C8130/35/45/55)
BSD 60.8 Image Input (High – C8170)
BSD 60.9 LPH Y & M
BSD 60.10 LPH C & K
BSD 60.11 Color Registration
BSD 60.12 Temperature and Humidity Sensing
Chain 70 Paper Supply
BSD 70.1 Tray 1 Paper Size Sensing
BSD 70.2 Tray 2 Paper Size Sensing
BSD 70.3 Tray 3 Paper Size Sensing (2TM)
BSD 70.4 Tray 3 Paper Size Sensing (TTM)
BSD 70.5 Tray 4 Paper Size Sensing (2TM)
BSD 70.6 Tray 4 Paper Size Sensing (TTM)
BSD 70.7 Bypass Tray Paper Size Sensing
BSD 70.8 Tray 1 Paper Stacking
BSD 70.9 Tray 2 Paper Stacking
BSD 70.10 Tray 3 Paper Stacking (2TM/TTM)
BSD 70.11 Tray 4 Paper Stacking (2TM)
BSD 70.12 Tray 4 Paper Stacking (TTM)
BSD 70.13 Bypass Tray Paper Sensing and Stacking
BSD 70.14 IOT and 2TM Paper Path and Drive Transmission (Low/Mid)
BSD 70.15 IOT and TTM Paper Path and Drive Transmission (Low/Mid/High)
Chain 80 Paper Transportation
BSD 80.1 Tray 1 and 2 Paper Pre-feeding (Mid/High)
BSD 80.2 Tray 3 and 4 Paper Pre-Feeding
BSD 80.3 Tray 1 and Bypass Tray Paper Transport
BSD 80.4 Tray 2 Paper Transport
BSD 80.5 2TM Paper Transport
BSD 80.6 TTM Paper Transport
BSD 80.7 Registration
Chain 90 Xerographics
BSD 90.1 NOT USED
BSD 90.2 NOT USED
BSD 90.3 Drum Life Control (Y, M)
BSD 90.4 Drum Life Control (C, K)
BSD 90.5 Toner Cartridge Life Control (Y, M)
BSD 90.6 Toner Cartridge Life Control (C, K)
BSD 90.7 Toner Cartridge Cooling (Mid/High)
BSD 90.8 Toner Dispense
BSD 90.9 Charging and Exposure Y
BSD 90.10 Charging and Exposure M
BSD 90.11 Charging and Exposure C
BSD 90.12 Charging and Exposure K
BSD 90.13 Development Y
BSD 90.14 Development M
BSD 90.15 Development C
BSD 90.16 Development K
BSD 90.17 1st BTR Contact/Retract
BSD 90.18 Image Transfer to IBT
BSD 90.19 Image Transfer to Paper
BSD 90.20 Waste Toner Disposal
BSD 90.21 Marking Air Flow
BSD 90.22 Marking Air Flow (High only)

8. PRODUCT TECHNICAL OVERVIEW
Product Technical Overview
Power
Input Power
Machine Run Control
Machine Run Control
Main Drives and NOHAD
Main Drives
NOHAD
User Interface
User Interface (UI)
Image Input
DADF
IIT
Image Output
Image Output
Media Supply
Media Supply
Paper Transport
Paper Transport
Xerographics
Xerographics
Fusing
Fusing
Print Transport
Print Transport