Brother DCP-1510, DCP-1511, DCP-1512, DCP-1518, Brother MFC-1810, MFC-1811, MFC-1813, MFC-1815, MFC-1818, Service Manual

Service Manual Brother DCP-1510, DCP-1511, DCP-1512, DCP-1518, Brother MFC-1810, MFC-1811, MFC-1813, MFC-1815, MFC-1818;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Brother.
You can print, zoom or read any diagram, picture or page from this Service Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Brother DCP-1510, DCP-1511, DCP-1512, DCP-1518, Brother MFC-1810, MFC-1811, MFC-1813, MFC-1815, MFC-1818. You can find easily everything what do you need.
To see what contain, please read table of contents:

REGULATION
SAFETY INFORMATION

CHAPTER 1. TROUBLESHOOTING
1. INTRODUCTION
1.1 Checks before Commencing Troubleshooting
2. OVERVIEW
2.1 Cross-section Drawing
2.1.1 Printer part
2.1.2 Scanner part
2.2 Paper Feeding
2.2.1 Printer part
2.2.2 Scanner part
2.3 Operation of Each Part
2.4 Block Diagram
2.5 Main Components
3. ERROR INDICATIONS
3.1 Error Codes
3.2 Error Messages
3.3 Connection Error
4. TROUBLESHOOTING
4.1 Error Cause and Remedy
4.2 Troubleshooting for Paper Feeding Problems
4.2.1 No paper is fed from the paper tray
4.2.2 Paper becomes wrinkled
4.2.3 Paper is curled
4.2.4 Paper is jammed
4.3 Image Defects
4.4 Troubleshooting According to Image Defect
4.4.1 Light
4.4.2 Faulty registration
4.4.3 Dark
4.4.4 Poor fixing
4.4.5 Completely blank
4.4.6 Image distortion
4.4.7 All black
4.4.8 Dirt on the back of paper
4.4.9 Vertical streaks
4.4.10 Black vertical streaks on a light background
4.4.11 Black horizontal stripes
4.4.12 White vertical streaks
4.4.13 White horizontal streaks
4.4.14 Faint print
4.4.15 White spots
4.4.16 Black spots
4.4.17 Black band
4.4.18 Downward fogging of solid color
4.4.19 Horizontal lines
4.4.20 Ghost
4.4.21 Fogging
4.5 Troubleshooting for Software Problems
4.5.1 Cannot print data
4.6 Troubleshooting for Control Panel Problems
4.6.1 Nothing is displayed on the LCD
4.6.2 Control panel is inoperable
4.7 Troubleshooting for Toner and Drum Problems
4.7.1 Replaced the toner cartridge with a new one
but still seeing error message prompting toner cartridge replacement
4.7.2 Toner cartridge cannot be detected
4.7.3 Failed to detect toner cartridge
4.7.4 Drum error
4.7.5 Drum unit cannot be detected
4.7.6 Replace drum unit (replaced the drum unit with a new one
but still seeing LED display prompting toner cartridge replacement)
4.8 Troubleshooting for Fuser Unit Problems
4.8.1 Fuser unit failure
4.9 Troubleshooting for Laser Unit Problems
4.9.1 Laser unit failure
4.10 Troubleshooting for Document Paper Feeding Problems
4.10.1 No document is fed
4.10.2 Multiple documents are fed
4.10.3 Document becomes jammed
4.10.4 Document becomes wrinkled
4.10.5 Document size is not detected correctly
4.11 Troubleshooting for Scanned Image Defects
4.11.1 Defect examples
4.11.2 Troubleshooting according to image defect
4.12 Troubleshooting for FAX/Phone Problems
4.12.1 Fax cannot be sent
4.12.2 Fax cannot be received
4.12.3 Ringtone does not sound
4.12.4 Telephone communication is unavailable
4.12.5 Communication error occurs
4.13 Troubleshooting for Other Problems
4.13.1 Machine does not turn ON
4.13.2 Main motor failure
4.13.3 Unusual noise is coming from the machine
4.13.4 Memory failure
4.13.5 Print failure

CHAPTER 2. DISASSEMBLY/REASSEMBLY
1. PACKING
2. TIGHTENING TORQUE LISTS
3. LUBRICATION
4. OVERVIEW OF GEARS
5. HARNESS ROUTING
6. DISASSEMBLY FLOW CHART
7. DISASSEMBLY PROCEDURE
7.1 Preparation
7.2 Side cover R
7.3 ADF unit (only for models with ADF unit)
7.3.1 Hinge
7.3.2 Document stopper
7.3.3 ADF cover
7.3.4 Handle cover
7.3.5 Document cover support
7.3.6 Document cover
7.3.7 Document separate roller holder ASSY
7.4 Document scanner unit / Document cover (only for models without ADF unit)
7.4.1 CIS unit / CIS flat cable
7.5 Panel unit
7.6 Low voltage power supply PCB unit
7.7 High voltage power supply PCB ASSY
7.8 Modem PCB ASSY (only for models with modem PCB)
7.9 Main PCB ASSY
7.10 Top cover ASSY
7.11 Side cover L
7.12 Handset holder (only for models with handset)
7.13 Fuser unit
7.14 Back cover
7.15 Tray cover ASSY
7.16 Front cover
7.17 Laser unit
7.18 Motor encoder PCB ASSY
7.19 Eject sensor PCB ASSY
7.20 Paper feed/paper printing position sensor PCB ASSY
7.21 New toner sensor PCB ASSY

CHAPTER 3. ADJUSTING AND UPDATING SETTINGS AS REQUIRED AFTER
PARTS REPLACEMENT
1. IF YOU REPLACE THE MAIN PCB ASSY
1.1 Installing Main Firmware
1.1.1 Checking firmware version
1.1.2 Installing main firmware
1.2 Initializing the EEPROM of the Main PCB ASSY (function code: 01)
1.3 Setting by Country (function code: 74)
1.4 Installing Language Firmware (except for Chinese model)
1.5 Setting Serial Number and Entering Adjusted Value of Laser Unit
1.6 Acquiring White Level Data (function code: 55)
1.7 Setting Language (function code: 52) (only for CEE model)
1.8 Checking Printing and Scanning
2. IF YOU REPLACE THE LASER UNIT
2.1 Entering Adjusted Value of Laser Unit
3. IF YOU REPLACE THE DOCUMENT SCANNER UNIT OR CIS UNIT
3.1 Acquiring White Level Data (function code: 55)
4. IF YOU REPLACE THE LOW VOLTAGE POWER SUPPLY PCB UNIT
4.1 Resetting Irregular Power Supply Detection Counter
5. IF YOU REPLACE THE PANEL ASSY
5.1 Checking LCD Operation (function code: 12)
5.2 Checking Control Panel Operation (function code: 13)

CHAPTER 4. SERVICE FUNCTIONS
1. MAINTENANCE MODE
1.1 How to Enter Maintenance Mode
1.1.1 Method of entering end-user accessible maintenance mode
1.1.2 Method of entering maintenance mode for service personnel
1.2 List of Maintenance Mode Functions
1.3 Details of Maintenance Mode Functions
1.3.1 Initialize EEPROM parameters (function code: 01, 91)
1.3.2 Print white level / black level data for document scanning compensation
(function code: 05)
1.3.3 Move CIS unit to transportation position (function code: 06)
1.3.4 ADF performance test (function code: 08)
1.3.5 Monochrome image quality test pattern (function code: 09)
1.3.6 Set worker switches (WSW) and print worker switch setting data
(function code: 10, 11)
1.3.7 Check LCD operation (function code: 12)
1.3.8 Check control panel button operation (function code: 13)
1.3.9 Display software version (function code: 25)
1.3.10 Check sensor operation (function code: 32)
1.3.11 Set PC print functions (function code: 43)
1.3.12 Change USB No. return value (function code: 45)
1.3.13 Set country / language (function code: 52)
1.3.14 Transfer received fax data / log information (function code: 53)
1.3.15 Fine-tune scanning position (function code: 54)
1.3.16 Acquire white level data and set CIS scan area (function code: 55)
1.3.17 Print test (function code: 67)
1.3.18 Print frame pattern (single-side printing) (function code: 69)
1.3.19 Print test pattern (function code: 71)
1.3.20 Setting by country (function code: 74)
1.3.21 Print maintenance information (function code: 77)
1.3.22 Display machine log information (function code: 80)
1.3.23 Display machine error code (function code: 82)
1.3.24 Send communication log information to telephone line (function code: 87)
1.3.25 Quit maintenance mode (function code: 99)
2. OTHER SERVICE FUNCTIONS
2.1 Manual Toner Reset Functions
2.2 Drum Counter Reset Functions (only for ten-key pad model)
2.3 Display ROM Version

APPENDIX 1 SERIAL NUMBERING SYSTEM
APPENDIX 2 DELETING USER SETTING INFORMATION

Number of pages: 184.