HP Latex 300 Latex 310 Latex 330 Latex 360 Service Manual and Parts List Manual

Service Manual and Parts List Manual HP Latex 300 Latex 310 Latex 330 Latex 360;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your HP Latex.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of HP Latex 300 Latex 310 Latex 330 Latex 360. You can find easily everything what do you need.
To see what contain, please read table of contents:

1. PRINTER SYSTEMS
Electrical system
Substrate path
Ink Delivery System (IDS)
Scan axis and carriage
Service station and waste management
Heating system
Front panel

2. TROUBLESHOOTING
Troubleshooting the printer
Troubleshooting system error codes
Performing a service test on a failed assembly
Performing the necessary service calibrations
The printer does not power on
How to read the power switch LEDs
How to read the Formatter LEDs
How to read other LEDs
Voltage check at installation
Troubleshooting substrate jams or printhead crashes
The printer continuously rejects printheads
The cutter does not function (Latex 360 only)
Troubleshooting the printer heaters
How to interpret the service information pages
How to obtain the printer log and the diagnostics package

3. SYSTEM ERROR CODES
Introduction
System error codes and warnings-explanation
Continuable and non-continuable error codes

4. SERVICE TESTS, UTILITIES AND CALIBRATIONS
Introduction
Initialization Self Test
Diagnostic Menu
Service Menu

5. PRINT QUALITY
Initial print-quality troubleshooting actions
RIP and front panel settings
How to use the print-quality plots
Printhead alignment status plot
Printhead health test plot
Optimizer health test plot
Substrate-advance test plot
Advanced printhead health test plot
Advanced alignment diagnostic print
Plot for escalation only
Geometry check
Scan-axis check
Misregistration check
Force drop detection
Troubleshooting non-uniform curing
Substrate advance issues

6. INK SUPPLIES
What are ink supplies?
Waste management system
General information about the ink supplies
General precautions when handling ink supplies
Priming the ink system
When should you replace the ink supplies?
Obtaining ink cartridge and printhead information
Troubleshoot ink cartridge and printhead issues
The front panel recommends replacing or reseating a printhead
Warranty information for ink supplies

7. PARTS AND DIAGRAMS
Printer Support
Left Cover
Right cover
Front Covers
Top and Rear Covers
Left Side Assemblies
Right Side Assemblies
Scan Axis Assemblies
Carriage Assemblies
Electronics
Drive Roller and Substrate Axis motor
Substrate path
Center Guide and Pinchwheels
Substrate Input Assemblies
Curing Assemblies
Curing Fans Assemblies
Printzone and Ink Collector
Take-Up Reel
Miscellaneous Parts

8. REMOVAL AND INSTALLATION
Introduction
Customer Self Repair parts
Service calibration guide to removal and installation
Drive roller
Front panel
Right cover
Left cover
Left impinging module cover
Right impinging module cover
Rear cover
Top cover
Right connector cover
E-box extension
Window sensor
Belt assembly
E-box
Impinging pressure sensor
Impinging recirculation cover
Impinging heater module
Impinging air curtain
Impinging air curtain thermal switch
Impinging air curtain resistors
Impinging air curtain fans
Room-temperature sensor
Impinging holding brackets
Impinging heater-controller enclosure
Window trims
Output platen
Input roller
Maintenance-cartridge door
Maintenance-cartridge door sensor
Substrate sensor
Right rollfeed module assembly
Left rollfeed module assembly
Take-up reel motor
Take-up reel left module
Take-up reel deflector supports
Tension bar
Take-up reel sensors
Line sensor assembly
Color sensor assembly
Color sensor actuator assembly
Cartridge tray
Opening the window
Window
Top cover fans
Rear fans
Scan-axis motor
Oiler assembly
Lubrication felts
Floater and PIP assembly
Under-carriage protector assembly
Front tube shelf
Rear tube shelf
Aerosol fan assembly
Spit roller motor
Cleaning roll motor assembly
Rewinder
Primer assembly
Primer valves
Primer valves cable
Service station
Drop detector
Cutter assembly
Ink Supply Station (ISS)
APS assembly
Encoder strip and encoder sensor
Carriage PCA
Carriage flex cables
Carriage assembly
Ink supply tubes and trailing cable
Static front platens (360)
Static front platens (330)
Static front platens (310)
Substrate-axis motor
Encoder disc and sensor
Substrate lever assembly
Substrate lever sensor
Ink Collector sensor
Ink Collector sensor cable
Vacuum rubbers
Roller gear protector
Print-zone lockers
OMAS
OMAS cable
Pinchwheel assembly
Individual pinchwheel rollers
Vacuum fan
Vacuum fan cable
Carriage bushings
Formatter battery
Solid State Drive (SSD)
Heater control assembly fan
Heater control assembly
Ink supply station PCAs
Interconnect PCA
Formatter PCA
OMAS controller PCA
Power Supply Unit (PSU)
PrintMech PCA
Engine PCA
Printer ID PCA
Air curtain and print-zone heater control PCA
Curing Control PCA
Curing power interconnect PCA
LAN PCA
Inner light PCA
Entry Mylar
Heater Control

9. PREVENTIVE MAINTENANCE
Moisture on the printer
Belt swelling
Clean the printer
Clean and lubricate the carriage rail
Clean the encoder strip
Scheduled maintenance
Level of printer usage

10. REPACKAGING INSTRUCTIONS
Reuse packaging material
Removing consumables
Reinstalling retention parts
Securing with adhesive tape
Covering the printer
Special checks before turning on the printer

11. SAFETY PRECAUTIONS
General safety guidelines
Electrical shock hazard
Heat hazard
Fire hazard
Mechanical hazard
Scan-axis encoder strip hazard
Lifting and handling
Warning labels
INDEX

Number of pages: 477.