Mimaki CG-60SR CG-60SL Service Manual and Parts List Manual

Service Manual and Parts List Manual Mimaki CG-60SR CG-60SL;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Mimaki.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Mimaki CG-60SR CG-60SL cutting plotter. You can find easily everything what do you need.
To see what contain, please read table of contents:

CHAPTER 1. OUTLINE OF MAINTENANCE
1-1. Precautions in Maintenance
1-1-1. Notes on repair
1-1-2. Preliminary checks
1-2. Tools required for maintenance work
1-2-1. Tools to be used at disassembly and reassembly
1-2-2. Adjustment tools
1-3. Specifications of the main unit
1-3-1. List of specifications
1-3-2. Conditions for ensuring the verified repeatability
1-3-3. Control panel and special key operation

CHAPTER 2. DISASSEMBLY AND REASSEMBLY
2-1. Outline
2-1-1. Precautions in disassembly and reassembly
2-1-2. Symbols used in this chapter
2-1-3. Disassembly
2-2. Disassembly and Reassembly of Exterior Parts
2-2-1. Y cover 60 and KEY PCB assembly
2-2-2. Left and right cover assemblies
2-2-3. Platen assembly and Platen covers
2-3. Disassembly and Reassembly of Carriage-related Parts
2-3-1. Pen assembly (CG-60SR and SL) and light pointer (CG-60SR only)
2-3-2. Mark sensor assembly (CG-60SR only)
2-3-3. Pulley BRG
2-3-4. Head PCB assembly
2-4. Disassembly and Reassembly of Drive-related Parts
2-4-1. Y motor (DC motor assembly) and M pulley
2-4-2. X motor (DC motor assembly), M pulley and X pulley
2-4-3. Spike shaft 60
2-4-4. Y belt 60, and tension pulley assembly
2-5. Disassembly and Reassembly of Electrical System Components
2-5-1. Main PCB assembly
2-5-2. Power supply PCB
2-5-3. Paper sensor 60 assembly
2-5-4. FAN assembly

CHAPTER 3. EXPLANATION OF ELECTRICAL PARTS
3-1. Outline
3-2. PCB Specifications
3-2-1. Power supply PCB
3-2-2. Main PCB
3-2-3. Key PCB
3-2-4. Head PCB
3-3. Electric Block Diagram

CHAPTER 4. TROUBLESHOOTING
4-1. Outline
4-1-1. Rough identification of the source of the trouble
4-1-2. Checking procedure
4-2. Troubles for which error messages are displayed
4-2-1. List of messages
4-2-2. Troubleshooting when error message is displayed
4-2-3. Troubleshooting when warning message is displayed
4-2-4. Action to be taken when general message is displayed
4-2-5. Status display
4-3. Troubles without error messages displayed
4-3-1. Outline
4-3-2. Troubles in startup or power supply
4-3-3. Troubles with the carriage and related components
4-3-4. Troubles in paper feeding or paper ejecting
4-3-5. Troubles with keyboard and related components
4-3-6. Troubles in connection or communication
4-3-7. Other troubles

CHAPTER 5. ADJUSTMENT
5-1. Outline
5-1-1. List of adjustment items
5-1-2. List of maintenance items
5-1-3. Opening of maintenance mode
5-2. ADJUSTMENT items
5-2-1. $ZI COMMAND
5-2-2. $PEN No. ASSIGNMENT
5-2-3. $BUFFER DUMP
5-2-4. $400mm SQUARE
5-2-5. $PEN PRESSURE
5-2-6. $PEN LANDING
5-2-7. $MOTOR CURRENT
5-2-8. Adjusting the location of mark sensor (photo sensor)(CG-60SR only)
5-2-9. $PHOTO SENSOR (Adjusting the sensitivity of mark sensor (photo sensor))(CG-60SR only)
5-2-10. Testing the mark sensor (photo sensor)(CG-60SR only)
5-2-11. $PHOTO SENSOR (Adjusting the position of mark sensor)(CG-60SR only)
5-2-12. Offset adjustment of light pointer (CG-60SR only)
5-2-13. $DEFAULT SET
5-3. #TEST items
5-3-1. &TEST PATTERN
5-3-2. &FEED TEST 2m
5-3-3. &PARAMETER DRAW
5-3-4. &PARAMETER DRAW2
5-3-5. &A SERVO TEST
5-3-6. &B SERVO TEST
5-3-7. &AB SERVO TEST
5-3-8. &SENSOR TEST
5-3-9. &KEYBOARD TEST
5-3-10. &DISPLAY TEST
5-3-11. &LCD TEST
5-3-12. &ROM/RAM CHECK
5-4. System parameter

CHAPTER 6. APPENDIX
6-1. Maintenance Operation Flow
6-2. Initial Operation Flow
6-3. Mark Detection Operation Flow
6-4. Updating the Firmware
6-4-1. Outline
6-4-2. CG-SR/SL Series updating procedure
6-5. Use of F/W Update Tool for Cutting Plotter
6-5-1. Outline
6-5-2. Upload (Backing up parameters)
6-5-3. Download (Restoring the parameters)
6-5-4. Troubleshooting for Update Tool

————

Content for Parts List Manual:
COVER, Y-BAR ASSY
PEN, MARK ASSY
PEN, MARK ASSY
SLIDER ASSY
FRAME ASSY
X-DRIVE ASSY
Y-DRIVE ASSY
CLAMP ASSY
ELECTRICAL UNIT ASSY
ROLL ASSY. (SR)
ROLL ASSY. (SL)
CHANGE TRACKING

*Addendum