Service Manual and Parts List Manual Roland CammJet ProII CJ-540 SolJet ProII SC-540;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland CammJet ProII CJ-540 SolJet ProII SC-540. You can find easily everything what do you need.
To see what contain, please read table of contents:
1) Structure & Spare Parts
1-1 COVERS
1-2 FRAME
1-3 HEAD CARRIAGE
1-4 DRIVE UNIT
1-5 CHASSIS
1-6 PINCH ROLLER
1-7 STAY ROLL
1-8 TOOL CARRIAGE
1-9 WIPER SYATEM
1-10 PUMP SYSTEM
1-11 INK SYSTEM
1-12 BASE FRAME
1-13 ACCESSORIES & STAND
1-14 TUC-1 CONTROLLER
1-15 TUC-1 OTHERS
1-16 TUC-1 ACCESSORIES
1-17 TU-550
2) Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 HEAD / SERVO BOARD
2-4 SUB BOARD
2-5 TUC-1
2-6 MAINTENANCE PARTS LIST
3) Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 WIPER REPLACEMENT
3-3 CAP TOP REPLACEMENT
3-4 TOOL CARRIAGE REPLACEMENT
3-5 CARRIAGE MOTOR REPLACEMENT
3-6 PUMP REPLACEMENT
3-7 INK TUBE REPLACEMENT
3-8 BOARDS REPLACEMENT
3-9 CARRIAGE WIRE REPLACEMENT
3-10 ENCODER SCALE REPLACEMENT
3-11 PINCH ROLLER REPLACEMENT
3-12 CUTTER PROTECTION REPLACEMENT
4) Adjustment
4-1 SPECIAL TOOLS
4-2 SERVICE MODE
4-3 HOW TO UPGRADE FIRMWARE
4-4 HEAD ALIGNMENT
4-5 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
4-6 LINEAR ENCODER SETUP
4-7 CROP MARK SENSOR ADJUSTMENT
4-8 TOOL/CROP MARK SENSOR POSITION ADJUSTMENT
4-9 PRINT/CUT POSITION ADJUSTMENT
4-10 CALIBRATION (FEEDING DIRECTION)
4-11 TOOL HEIGHT ADJUSTMENT
4-12 TOOL PRESSURE ADJUSTMENT
4-13 CARRIAGE WIRE TENSION ADJUSTMENT
4-14 NETWORK BOARD INITIALIZE
5) Supplemental Information
5-1 SENSOR MAP
6) Troubleshooting
6-1 WHITE FINE LINES / BANDING / MISSING DOT / SCRATCHY PRINTING / BLURRED PRINTING
6-2 IT DOESN’T PRINT AT ALL
6-3 INK DROPS ON MEDIA
6-4 SHIFTING IN PRINTING
6-5 VERTICAL BANDING
6-6 PRINT DOES NOT MATCH WITH CUT
6-7 STITCH CUT
6-8 START AND END POINTS DO NOT MATCH
6-9 DISTORTED FIGURE
6-10 MEDIA SHIFTING
6-11 MOTOR ERROR
6-12 ERROR MESSAGE
SERVICE CALL
7) Service Activities
7-1 INSTALLATION CHECK LIST
7-2 MAINTENANCE CHECK LIST
7-3 SPECIFICATION
Roland CammJet ProII ProIICJ540 CJ540 SolJet ProII SC540 ProIISC540 SJ CJ
Roland CammJet ProII CJ-540 SolJet ProII SC-540 and Technical Documentation
The documentation available for the Roland CammJet ProII CJ-540 SolJet ProII SC-540 and is designed to support maintenance, troubleshooting and component-level servicing.
Depending on the document type, the parts list manual may include service procedures, exploded parts diagrams, adjustment sequences, wiring references and diagnostic information used during repair operations.
Technicians use these manuals to identify faults, replace components correctly and maintain equipment according to manufacturer service specifications.