Roland VersaCamm VP540 Roland VersaCamm VP300 Service Manual and Parts List Manual

Service Manual and Parts List Manual Roland VersaCamm VP-540 Roland VersaCamm VP-300;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland VersaCamm plotter.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland VersaCamm VP-540 Roland VersaCamm VP-300. You can find easily everything what do you need.
To see what contain, please read table of contents:

1) Structure & Spare Parts
1-1 COVERS
1-2 FRAME
1-3 DRIVE UNIT
1-4 HEAD CARRIAGE (VP-540)
1-5 HEAD CARRIAGE (VP-300)
1-6 BASE FRAME
1-7 CHASSIS
1-8 PINCH ROLLER
1-9 STAND
1-10 TOOL CARRIAGE
1-11 WIPER SYSTEM
1-12 PUMP SYSTEM
1-13 INK SYSTEM
1-14 ACCESSORIES

2) Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 SERVO BOARD
2-4 CARRAGE BOARD
2-5 SUB BOARD
2-6 MAINTENANCE PARTS LIST

3) Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 WIPER REPLACEMENT
3-3 CAP TOP REPLACEMENT
3-4 TOOL CARRIAGE REPLACEMENT
3-5 CARRIAGE MOTOR REPLACEMENT
3-6 FEED MOTOR REPLACEMENT
3-7 PUMP REPLACEMENT
3-8 INK TUBE REPLACEMENT
3-9 BOARD REPLACEMENT (MAIN BOARD SW POWER SUPPLY)
3-10 BATTERY REPLACEMENT
3-11 CARRIAGE BELT REPLACEMENT
3-12 ENCODER SCALE REPLACEMENT
3-13 GRIT ENCODER REPLACEMENT
3-14 PINCH ROLLER REPLACEMENT
3-15 CUTTER PROTECTION REPLACEMENT

4) Adjustment
4-1 SERVICE MODE
4-2 HOW TO UPGRADE FIRMWARE/INSTALL FIRMWARE
4-3 HOW TO UPGRADE FIRMWARE OF THE NETWORK CONTROLLER
4-4 HEAD ALIGNMENT
4-5 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
4-6 LINEAR ENCODER SETUP
4-7 FLUSHING POSITION ADJUSTMENT
4-8 CROP MARK SENSOR ADJUSTMENT
4-9 CROP-CUT ADJUSTMENT
4-10 PRINT/CUT POSITION ADJUSTMENT
4-11 CALIBRATION(FEEDING DIRECTION)
4-12 TOOL HEIGHT ADJUSTMENT
4-13 TOOL PRESSURE ADJUSTMENT
4-14 BELT TENSION ADJUSTMENT
4-15 BELT POSITION ADJUSTMENT
4-16 TAKE-UP UNIT OPERATION CHECK

5) Supplemental Information
5-1 SPECIAL TOOLS
5-2 SENSOR MAP

6) Troubleshooting
6-1 DEFECT OF PRINT QUALITY (BANDING/SCRATCHY PRINTING/BLURRED PRINTING)
6-2 PARTICULAR COLOR IS NOT PRINTED AT ALL
6-3 SHIFTING IN PRINTING / COLOR SHIFTING
6-4 INK DROPS ON THE MEDIA
6-5 VERTICAL BANDING
6-6 MISSING DOT OR DEFLECTED-FIRED DOT APPEARS WHEN PERFORMING PRINTING WITH LONG DELAY
6-7 PRINT & CUT MISALIGHMENT
6-8 POOR CUTTING QUALITY(STITCH CUT, DISTORTED CUT, MISMATCHED START AND END POINTS)
6-9 MEDIA SKEW
6-10 MOTOR ERROR
6-11 HEATER/DRYER TEMPERATURE DOES NOT GO UP
6-12 PROBLEM IN NETWORK(RIP DOES NOT RECOGNIZE THE PRINTER)
6-13 ERROR MESSAGE
6-14 SERVICE CALL

7) Service Activities
7-1 INSTALLATION CHECK LIST
7-2 MAINTENANCE CHECK LIST
7-3 SPECIFICATION