Sharp Color Led Printer AR-C265P Service Manual

Service Manual Sharp Color Led Printer AR-C265P;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Sharp Color Led Printer AR-C265P copier.
You can print, zoom or read any diagram, picture or page from this Service Manual. Every chapter on this manual is fully detailed and contain all the  simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Sharp Color Led Printer AR-C265P photocopier. You can find easily everything what do you need.
To see what contain, please read table of contents:

CHAPTER 1: CONFIGURATION
I. SYSTEM CONFIGURATION
II. PRINTER CONFIGURATION
III. COMPOSITION OF OPTIONAL ITEMS
IV. SPECIFICATIONS
V INTERFACE SPECIFICATIONS
A. Parallel interface specifications (N/A)
B. USB interface specifications
C. Network interface specifications

CHAPTER 2: EXPLANATION OF OPERATION
I. ELECTROPHOTOGRAPHIC PROCESSING MECHANISM
II. PRINTING PROCESS

CHAPTER 3: INSTALLATION
I. CAUTIONS, AND DO’S AND DON’TS
II. UNPACKING METHOD
III. PRINTER INSTALLATION INSTRUCTIONS
IV. LISTING OF COMPONENT UNITS AND ACCESSORIES
V.  ASSEMBLING METHOD
A.  Assembly of printer main body
B. Connection of power cable
C. Installation of optional items
D. Confirmation of recognition of optional items
VI. MENU MAP PRINT
VII. CONNECTION METHODS
VIII. CONFIRMATION OF PAPER USED BY THE USER

CHAPTER 4: REPLACEMENT OF PARTS
I. PRECAUTIONS ON THE REPLACEMENT OF PARTS
A. Maintenance tools
II. PART REPLACEMENT METHODS
A. Left side cover
B. Right side cover
C. Face-up tray
D. Rear cover
E. LED assy/LED assy springs
F. Control PCB
G. Print engine controller PCB
H. Top cover assembly
I. Top cover
J. Controller panel assy
K. Board PRP/Top cover handle
L. Low-voltage power supply/low-voltage fan/hopping motor/fuser motor
M. Guide eject assy/color register assy/board-PRY
N. Fan (fuser)/belt motor/high-voltage power supply board/cover-open switch
O. MPT assy
P. Feeder unit/board-RSF/MPT hopping roller/frame assy separator/cover front
Q. Board-PRZ lift-up motor/solenoid/paper-end sensor
R. Feed roller
S. Shaft eject assy(FU)/shaft eject assy(FD)/eject sensor
T. Fuser Unit
U. Belt Unit
III. LUBRICATING POINTS

CHAPTER 5: MAINTENANCE MENUS
I. SYSTEM MAINTENANCE MENU (FOR MAINTENANCE PERSONNEL)
II. MAINTENANCE UTILITY
III. FUNCTIONS OF USER’S MAINTENANCE MENU
A. Maintenance menu (For end users)
B. Self-diagnostic mode
IV. SETUP AFTER REPLACEMENT OF PARTS
A. Precautions on the replacement of engine control PCB
B. Setup of EEPROM after replacement of SP1/TBH PCB
C. Setup of destination
V. ABOUT THE MANUAL SETUP OF PRINT DENSITY ADJUSTMENT

CHAPTER 6: PERIODICAL MAINTENANCE
I. RECOMMENDED REPLACEMENT PARTS
II. CLEANING
III. CLEANING OF LED LENS ARRAY
IV. CLEANING OF PICKUP ROLLERS
V. INTERNAL CLEANING OF PRINTER

CHAPTER 7: TROUBLESHOOTING PROCEDURES
I. PRECAUTIONS PRIOR TO REPAIR
II. ITEMS TO BE CHECKED PRIOR TO TAKING ACTION ON ABNORMAL IMAGES
III. PRECAUTIONS WHEN TAKING ACTION ON ABNORMAL IMAGES
IV. PREPARATIONS FOR TROUBLESHOOTING
V. TROUBLESHOOTING METHOD
A. LCD message list
B. Preparing for troubleshooting
C. Image problem troubleshooting
D. Actions after forced initialization of HDD/Flash
E. Network Troubleshooting
VI. CHECK OF FUSES

CHAPTER 8: CONNECTION DIAGRAMS
I. CHECK OF RESISTANCE VALUES
II. COMPONENT LAYOUT

Number of pages: 237.