HP DesignJet 10000s, Service Manual & Parts List

Service Manual & Parts List HP DesignJet 10000s;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your HP DesignJet 10000s copier.
You can print, zoom or read any diagram, picture or page from this Service & Parts List Manual. Every chapter on this manual is fully detailed and contain all theĀ  simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of HP DesignJet 10000s photocopier. You can find easily everything what do you need.
To see what contain, please read table of contents:

TROUBLESHOOTING
Introduction
Troubleshooting System Error Codes
Performing a Service Test on a Failed Assembly
Performing the Necessary Service Calibrations or Adjustments
Solving Print Quality Problems
The Printer does not Power ON
Cover Sensors are not Working
The File Sent is Not Processed Immediately
Troubleshooting Media Jam Messages
Media Jams Occur Frequently
Print Speed is Very Slow
No Ink Message when there is Enough Ink
Abnormal Sound Coming from the Printer
Front Panel is Not Working
Heater Panel is Not Working
Solving Heater Problems
“Power ON Heater Power Switch” appears on Heater Panel
Heater Does NOT become Hot
Abnormal Temperature is Displayed
The Heater Temperature Becomes Extremely High
“Initializing” Continuously Appears on the Heater Panel
“Power Save Mode” Continuously Appears on the Heater Panel
Special Power On Procedure
Both NVRAM and Main PCA are Replaced Together

SYSTEM ERROR CODES
Introduction
Self-Diagnostic Errors at Power On
System Error Codes
Heater Error Codes
System Error Codes

HEAD ADJUSTMENT
Introduction
Tools Required
Calibrate the Printhead Adjustment Jig
Install the Printhead Adjustment Jigs in the Carriage
Set Printhead Voltage
Print the Printhead Adjustment Pattern
Perform Printhead Position Correction
Print the Check Printhead Pattern
Adjust the Printhead
Tip to Speed-Up the Printhead Adjustment

MAINTENANCE MODE
Introduction
Diagnostics – Self Test
Phone Support
Maintenance Mode Menus
Entering the Maintenance Mode
Basic Menu Operation
P. ADJ. (Printer Adjustment)
PH. ADJ (Printhead Adjustment)
PH. MAIN (Printhead Maintenance)
MNFG-PRN (Manufacturing Patterns)
SETUP
FEED
SENSORS
ELECT (Electronics)
VOLT (Voltage Check)
MOTORS
SYSTEM INF
COUNTER
Heater Panel Maintenance Mode

ADEJUSTMENTS AND CALIBRATIONS
Adjustments and Calibrations
Adjustments
Belt Tension Adjustment
Carriage Height Adjustment
Scan-Axis Belt Tension Adjustment
Paper-Axis Belt Tension Adjustment
Timing Belt (for Feed/TUR Unit) Tension Adjustment
Wiping Station Height Adjustment
Wiper Belt Tension Adjustment
Wiper Blade Height Adjustment
Capping Station Height Adjustment
Printhead Capping Limit Adjustment
Carriage Shield Height Adjustment
Media Feed and Take-Up-Reel Unit Adjustment
Media End Sensor Adjustment
Media Slack Sensor Adjustment
Take-Up-Reel Sensors Adjustment
Platen Flatness Measurement and Adjustment
Calibrations
Wiping Position Calibration
Capping Position Calibration
Line Sensor Calibration (Side Margin)
Line Sensor Calibration (Top Margin)

PRINT QUALITY
Print Quality
Print Quality Troubleshooting Actions
Print Quality General Advice
Troubleshooting Print Quality Problems
Horizontal Lines Across the Image (Banding)
Images are Blurred
Bleeding, Repelling or Mottling Problems
Image is Completely Blank or Faded
Output Only Contains a Partial Print
The Printer Area is Stained
Part of Image is Missing at the Start of the Print
Print Quality is not Improved After Printhead Recovery
Troubleshooting Printhead Problems

PARTS AND DIAGRAMS
Right Hand Covers
Left Hand Covers
Center Covers
Electronics Module
Control Panels
Carriage Assembly
Scan-Axis Assemblies
Paper Path Assemblies
Media Entry Assemblies
Take-Up-Reel Assemblies
Capping Assemblies
Wiping Assemblies
Ink Supply and Subtank Assemblies
Printer Stand and Waste Bottle
Media Feed and TUR Sensors
Accessories
Service Tools

REMOVAL AND INSTALLATION
Introduction
Covers
Front Panel
Heater Panel
Front Heater
Rear Heater
Center Platen
Vacuum Fan
Main PCA
NVRAM
Head Relay Board
Add-On (HEB2) Control PCA
Switching Power Supply Unit
Power Supply Unit
Heater Relay Assembly
Waste Bottle Sensor
Front Media Sensor
Rear Media Sensor
Media Lever Sensor
Rear Cover Sensor
Home Position Sensor
Paper-Axis Motor and Belt
Scan-Axis Motor and Belt
Carriage Drive Assembly (Includes Carriage Belt)
Encoder Strip
Trailing Cable
Printhead Cooling Fans
Printhead
Printhead Connector Assembly
Carriage PCA
Air Damper
Encoder Sensor
Line Sensor
Ink Pump Assembly
Ink Supply Station (Left or Right)
IC Door Sensor (Left or Right)
Subtank Sensors
Capping Station Assembly
Capping Unit
Prime Assembly
Solenoid Assembly
Waste Bottle Holder and Sensor Assembly
Wiping Station Assembly
Wiper Cleaning Assembly
Wiper Blade
Wiper Belts
Pinchwheel Assembly
Drive Roller
Media Feed Drive Unit Assembly
Take-Up-Reel Drive Unit Assembly
Drive Unit Rollers
Drive Unit Timing Belt
Media Sensors (Media End, Media Slack and Take-Up-Reel)
White Nets (For Front and Rear Heaters)
Sub-Scroller Flange

PREVENTIVE MAINTENANCE
Printheads Maintenance
Daily Inspection and Maintenance
Wiper Blade Cleaning
Moistening the Wiper Sponge
Capping Unit Cleaning
Waste Ink Bottle Disposal
IQ Print
Normal Printhead Recovery
When Leaving the Printer Off for more than 2 weeks
When Returning to the Printer after more than 2 weeks
If the Printer is Switched Off for less than 2 weeks
If the Printer is Switched Off for more than one Month

Number of pages: 468.