Mutoh ValueJet VJ-1638W Service Manual and Parts List Manual

Service Manual and Parts List Manual Mutoh ValueJet VJ-1638W;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Mutoh ValueJet.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Mutoh ValueJet VJ-1638W. You can find easily everything what do you need.
To see what contain, please read table of contents:

1. SAFETY INSTRUCTION
1.1 Introduction
1.2 Types and Meanings of Warnings
1.3 Warning Labels
1.3.1 Handling the Warning Labels
1.3.2 Location and Type of Warning Labels

2. TROUBLESHOOTING
2.1 Introduction
2.2 Troubleshooting with Error Messages
2.2.1 Operation Status
2.2.2 Errors with Message
2.2.3 Errors Requiring Reboot
2.2.4 Error Messages During File Transmission
2.3 Troubleshooting Without Error Messages
2.3.1 Initial Operation Problems
2.3.2 Media Feed Problems
2.3.3 Printing Problems
2.3.4 Noise Problems
2.3.5 Online Function Problems
2.3.6 Other Problems
2.3.7 Problems in Using MUTOH Service Assistance

3. PARTS REPLACEMENT
3.1 Introduction
3.2 Removing Covers
3.2.1 Removing Maintenance Cover
3.2.2 Removing Maintenance Cover U
3.2.3 Removing Side Maintenance Cover
3.2.4 Removing IH Cover
3.2.5 Removing Side Top Cover
3.2.6 Removing Carteidge Cover
3.2.7 Removing Sub Tank Cover R
3.2.8 Removing Sub Tank Cover L
3.2.9 Removing Front Cover
3.2.10 Removing Top Cover
3.2.11 Removing Paper Guide F (Upper)
3.2.12 Removing Paper Guide R (Upper)
3.2.13 Removing Paper guide R (lower)
3.2.14 Removing Panel Cover
3.3 Replacing Cover Peripherals
3.3.1 Replacing Panel Unit
3.3.2 Replacing Panel FFC (Panel tape wires)
3.3.3 Replacing Cover switch Assy
3.3.4 Replacing Cover R Cable Assy
3.3.5 Replacing Cover L Cable Assy
3.3.6 Replacing Exhaust Fan
3.3.7 Replacing Exhaust fan Cable Assy
3.4 Replacing Board Base
3.4.1 Opening Board box
3.4.2 Replacing Power Board Assy
3.4.3 Replacing Cooling FAN(For MAIN Board Assy)
3.4.4 Replacing SODIMM
3.4.5 Replacing MAIN board Assy
3.4.6 Replacing AC Inlet
3.4.7 Replacing AC Cable Assy
3.4.8 Replacing MAIN_DC Cable Assy
3.4.9 Replacing JUNCTION board Assy
3.4.10 Replacing JUNC_ID Cable
3.4.11 Replacing JUNC_FFC
3.5 Replacing X Rail Section
3.5.1 Replacing X Speed Reduction Belt
3.5.2 Replacing PF Encoder
3.5.3 Replacing PF Encoder Scale, PF Speed Reduction Pulley
3.5.4 Replacing PF Motor Assy
3.5.5 Replacing PF Motor relay Assy
3.5.6 Replacing P_Rear Sensor
3.5.7 Replacing Lever sensor and Lever sensor cable Assy
3.5.8 Replacing Platen Non-Reflecting Tape
3.5.9 Replacing Media Holder
3.6 Replacing Y Rail section
3.6.1 Replacing Steel belt
3.6.2 Replacing CR Motor
3.6.3 Replacing CR Deceleration Belt
3.6.4 Replacing CR deceleration pulley
3.6.5 Replacing CR Motor Cable Assy
3.6.6 Replacing CR Return Pulley
3.6.7 Replacing T Fence
3.6.8 Replacing CR Origin Sensor
3.6.9 Replacing CR Origin Sensor Cable Assy
3.6.10 Replacing Steel Bare
3.6.11 Replacing CR_FFC
3.6.12 Replacing Ink Tube
3.6.13 Replacing Pressure Roller
3.7 Replacing Carriage lock
3.7.1 Releasing Carriage Lock
3.7.2 Replacing Carriage Lock Solenoid,
3.7.3 Replacing CR Lock Solenoid Cable Assy
3.7.4 Removing Carriage Cover
3.7.5 Removing CR board Cover
3.7.6 Replacing CR board Assy
3.7.7 Replacing CR Encoder Assy
3.7.8 Removing MSI Cover
3.7.9 Replacing Cutter Solenoid Cable Assy
3.7.10 Replacing Solenoid Head Assy
3.7.11 Replacing Print Head
3.7.12 Replacing Head FFC
3.7.13 Replacing P_EDGE Sensor
3.7.14 Replacing Cursor Roller Arm Assy
3.7.15 Replacing Carriage Assy
3.8 Replacing Maintenance Section
3.8.1 Removing Maintenance Inner Cover
3.8.2 Replacing Flushing Box
3.8.3 Replacing Flushing absorbent Assy
3.8.4 Replacing Wiper
3.8.5 Replacing Cap Head Assy
3.8.6 Replacing Maintenance Assy
3.8.7 Replacing Wiper Solenoid Cable
3.8.8 Replacing Pump motor Cable
3.8.9 Replacing Pump
3.8.10 Waste Fluid Sensor Cable Assy
3.8.11 Replacing Wiper Solenoid
3.9 Replacing IH section
3.9.1 Replacing Cartridge Holder Assy
3.9.2 Replacing Ink ID Board Assy
3.9.3 Replacing 2-way Solenoid Assy
3.9.4 Replacing 2-way Solenoid Cable Assy
3.9.5 Replacing Sub Tank Under Sponge Assy
3.9.6 Replacing Sub tank Assy?TANK_H/L Cable Assy
3.10 Replacing Leg Section
3.10.1 Replacing Waste Fluid Bottle and Waste Fluid Level Switch
3.11 Replacing Roll media holder Assy
3.12 Replacing Take-up Unit Section (Option)
3.12.1 Removing Tension Arm
3.12.2 Removing Take-up Unit
3.12.3 Removing Take-up Cover
3.12.4 Replacing Scroller
3.12.5 Replacing Take-up Control Board Assy
3.12.6 Replacing Take-up ON Sensor and Take-up OFF Sensor
3.12.7 Replacing Peripheral Devices of Take-up Motor Assy

4. ADJUSTMENT
4.1 Introduction
4.2 Adjustment Item
4.3 Working with MUTOH Service Assistance Software
4.4 Steel Belt Tension Adjustment
4.4.1 Jigs and Tools
4.4.2 Adjustment Procedure
4.5 CR Speed Reduction Belt Tension Adjustment
4.6 X Speed Reduction Belt Tension Adjustment
4.6.1 Jigs and Tools
4.6.2 Adjustment Procedure
4.7 Head Accuracy Adjustment
4.7.1 Head Alignment (Horizontal Slant)
4.7.2 Head Alignment (Front-Back Slant )
4.7.3 Head Alignment (Vertical Slant)
4.8 Head Height Adjustment
4.9 P_Rear/P_Edge Sensor Adjustment
4.10 Cutter position adjustment

5. SELF-DIAGNOSIS MODE
5.1 Introduction
5.2 Preparation
5.2.1 Preparations on Machine
5.2.2 Starting Up
5.3 Operations in Self-Diagnosis Mode
5.3.1 Operating Self-Diagnosis Mode
5.3.2 Diagnosis Items in Self-Diagnosis Menu
5.4 Inspection Menu
5.4.1 Memory Size Menu
5.4.2 Version Menu
5.4.3 Operation Panel Menu
5.4.4 Sensor Menu
5.4.5 Encoder Menu
5.4.6 Fan Menu
5.4.7 Record Menu
5.4.8 Head Waveform Menu
5.4.9 Time Check Menu
5.5 Ink Charging Menu
5.6 Adjustment Menu
5.6.1 Rear/ Edge Sensor Adjustment
5.6.2 Head Nozzle Check Menu
5.6.3 Skew Check Menu
5.6.4 Head Slant Check Menu
5.6.5 Uni-D/Bi-D Adjustment Menu
5.6.6 Bi-D Copy
5.6.7 Top&Bottom adjustment Menu
5.6.8 Test Printing Menu
5.6.9 Longstore Menu
5.6.10 Longstore2 Menu
5.6.11 Software Counter Initialization Menu
5.6.12 Feed Pitch Check Menu
5.7 Cleaning Menu
5.8 Sample Printing Menu
5.9 Parameter Menu
5.9.1 Parameter Initialization Menu
5.9.2 Parameter Update Menu
5.10 Servo Setting Menu
5.11 Endurance Running Menu
5.11.1 CR Motor Endurance Menu
5.11.2 PF Motor Endurance Menu
5.11.3 Cutter Endurance Menu
5.11.4 Pump Endurance Menu
5.11.5 Head Lock Menu
5.11.6 Wiper Endurance menu
5.11.7 Print Head Endurance (Nozzle Print) Menu
5.11.8 General Endurance Menu
5.11.9 Endurance Running Check Menu
5.12 Paper Feed Menu
5.13 Paper Initial Menu

6. MAINTENANCE MODE 2
6.1 Introduction
6.2 Operations in Maintenance Mode 2
6.2.1 Starting Up the Maintenance Mode 2
6.2.2 Operating Maintenance Mode 2
6.3 Maintenance Mode 2 Menu
6.3.1 Counter Indication Menu
6.3.2 Counter Initialization Menu
6.3.3 Cleaning Menu
6.3.4 Counter Print Menu
6.3.5 Paper Feed Menu

7. MAINTENANCE
7.1 Introduction
7.2 Periodical Services
7.2.1 Periodic Replacement Parts
7.2.2 Parts Which Require Inspection/Replacement
7.3 Part Life Information
7.4 Jigs and Tools
7.4.1 Required Tools
7.5 Lubrication/Bonding
7.6 Transportation of Product

8. PRODUCT OVERVIEW
8.1 Introduction
8.2 Part Names and Functions
8.2.1 Front Section
8.2.2 Rear Section
8.2.3 Operation Panel
8.3 Printer Status
8.3.1 Operating Status Type
8.3.2 Switching Operating Status
8.3.3 Selecting Panel Language

9. SPECIFICATIONS
9.1 Introduction
9.2 Product Specifications
9.2.1 Main Unit Specifications
9.3 Interface Specifications
9.3.1 Network Interface Specifications
9.4 Options/Supplies List
9.4.1 Supplies
9.5 Choosing a Place for the Printer

10. APPENDIX
10.1 Introduction
10.2 Maintenance Part List