Roland AdvancedJET AJ-1000 Service Manual and Parts List Manual

Service Manual and Parts List Manual Roland AdvancedJET AJ-1000;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland AdvancedJET.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland AdvancedJET AJ-1000. You can find easily everything what do you need.
To see what contain, please read table of contents:

1. Structure & Spare Parts
1-1 COVERS
1-2 FRAME (Serial No. ~ ZV40399)
1-3 FRAME (Serial No. ~ ZV40400)
1-4 CARRIAGE
1-5 DRIVE UNIT
1-6 BED
1-7 CHASSIS
1-8 PINCH ROLLER
1-9 MAINTENANCE LIQUID CARTRIDGE
1-10 WIPER SYSTEM
1-11 INK SYSTEM
1-12 SUBTANK SYSTEM
1-13 DRYER
1-14 STAND (Serial No. ~ ZW20567)
1-15 STAND (Serial No. ZW20568 ~)
1-16 TU UNIT
1-17 TU ROLL
1-18 ACCESSORIES

2. Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 HEAD BOARD
2-4 SERVO BOARD
2-5 HEATER BOARD
2-6 PUMP DRIVE BOARD
2-7 SUB BOARD
2-8 MAINTENANCE PARTS LIST

3. Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 WIPER REPLACEMENT
3-3 CAP TOP REPLACEMENT
3-4 CARRIAGE MOTOR REPLACEMENT
3-5 SUPPLY PUMP REPLACEMENT
3-6 INK TUBE REPLACEMENT
3-7 BOARDS REPLACEMENT (MAIN / SW POWER SUPPLY)
3-8 BATTERY REPLACEMENT
3-9 CARRIAGE BELT REPLACEMENT
3-10 ENCODER SCALE REPLACEMENT
3-11 TU BOARD REPLACEMENT

4. Adjustment
4-1 SPECIAL TOOL
4-2 SERVICE MODE
4-3 HOW TO UPGRADE FIRMWARE
4-4 HEAD ALIGNMENT
4-5 CAPPING POSITION ADJUSTMENT
4-6 LINEAR ENCODER SETUP
4-7 PAPER SIDE SENSOR ADJUSTMENT
4-8 CALIBRATION (FEEDING DIRECTION)
4-9 BELT TENSION ADJUSTMENT
4-10 BELT POSITION ADJUSTMENT
4-11 NETWORK BOARD INITIALIZE
4-12 LIMIT POSITION & MAX SCAN WIDTH INITIALIZE

5. Supplemental Information
5-1 SENSOR MAP
5-2 HOW TO REMOVE THE AIR IN THE INK LINE

6. Troubleshooting
6-1 WHITE FINE LINE / BANDING / MISSING DOT / SCRATCHY PRINTING / BLURRED PRINTING
6-2 PARTICULAR COLOR IS NOT PRINTED AT ALL
6-3 SHIFTING IN PRINTING / COLOR SHIFTING
6-4 INK DROPS ON THE MEDIA
6-5 VERTICAL BANDING
6-6 MISSING DOT OR DEFLECTED-FIRED DOT APPEARS WHEN PERFORMING PRINTING WITH LONG DELAY
6-7 INK EMPTY MESSAGE APPEARS EVEN IF THE INK HAS NOT RUN OUT
6-8 THE INK OR MAINTENANCE LIQUID NEVER COMES BY PERFORMING FILL INK
6-9 MOTOR ERROR
6-10 HEATER TEMPERATURE DOES NOT GO UP
6-11 DRYER TEMPERATURE DOES NOT GO UP
6-12 THE BLOWER FAN DOES NOT MOVE
6-13 THE TAKE-UP/FEED OUT UNIT DOES NOT MOVE
6-14 ERROR MESSAGE
6-15 SERVICE CALL
6-16 THE INFORMATION IN THE INK CARTRIDGE IC CANNOT BE READ PROPERLY/ THE INK CARTRIDGE REPORT SHOWS “Data Error”

7. Service Activities
7-1 INSTALLATION CHECK LIST
7-2 MAINTENANCE CHECK LIST
7-3 PREPARATION FOR TRANSPORTATION 1
7-4 PREPARATION FOR TRANSPORTATION 2
7-5 SPECIFICATION