Roland SolJet Pro III XJ-740 SolJet Pro III XJ-640 SolJet Pro III XJ-540 Service Manual and Parts List Manual

Service Manual and Parts List Manual Roland SolJet Pro III XJ-740 SolJet Pro III XJ-640 SolJet Pro III XJ-540;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Roland SolJet Pro III.
You can print, zoom or read any diagram, picture or page from this Service Manual and Parts List Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Roland SolJet Pro III XJ-740 SolJet Pro III XJ-640 So

    lJet Pro III XJ-540. You can find easily everything what do you need.
    To see what contain, please read table of contents:

    1) Structure & Spare Parts
    1-1 COVERS
    1-2 FRAME
    1-3 HEAD CARRIAGE
    1-4 DRIVE UNIT
    1-5 CHASSIS
    1-6 PINCH ROLLER
    1-7 WIPE SYSTEM
    1-8 CAP SYSTEM
    1-9 INK SYSTEM
    1-10 STAND
    1-11 TU CONTROLLER
    1-12 ACCESSORIES

    2) Electrical Section
    2-1 WIRING MAP
    2-2 MAIN BOARD
    2-3 HEAD BOARD
    2-4 SERVO BOARD
    2-5 HEATER BOARD
    2-6 INK SYSTEM BOARD
    2-7 SUB BOARD
    2-8 TAKEUP BOARD
    2-9 MAINTENANCE PARTS LIST

    3) Replacement of Main Parts
    3-1 HEAD REPLACEMENT
    3-2 WIPER REPLACEMENT
    3-3 CAP TOP REPLACEMENT
    3-4 CARRIAGE MOTOR REPLACEMENT
    3-5 PUMP REPLACEMENT
    3-6 INK TUBE REPLACEMENT
    3-7 BOARDS REPLACEMENT (HEAD / SERVO / MAIN / SW POWER SUPPLY)
    3-8 BATTERY REPLACEMENT
    3-9 CARRIAGE BELT REPLACEMENT
    3-10 ENCODER SCALE REPLACEMENT
    3-11 PINCH ROLLER REPLACEMENT
    3-12 TAKE-UP BOARD REPLACEMENT

    4) Adjustment
    4-1 SERVICE MODE
    4-2 HOW TO UPGRADE FIRMWARE/INSTALL FIRMWARE
    4-3 HOW TO UPGRADE FIRMWARE OF THE NETWORK CONTROLLER
    4-4 HEAD ALIGNMENT
    4-5 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
    4-6 PAPER SIDE SENSOR ADJUSTMENT
    4-7 LINEAR ENCODER SETUP
    4-8 CAP HEIGHT ADJUSTMENT
    4-9 CALIBRATION
    4-10 BELT TENSION ADJUSTMENT
    4-11 BELT POSITION ADJUSTMENT
    4-12 TAKE-UP UNIT OPERATION CHECK

    5) Supplemental Information
    5-2 SPECIAL TOOLS
    5-1 SENSOR MAP

    6) Troubleshooting
    6-1 WHITE FINE LINE / BANDING / MISSING DOT / SCRATCHY PRINTING / BLURRED PRINTING
    6-2 PARTICULAR COLOR IS NOT PRINTED AT ALL
    6-3 SHIFTING IN PRINTING / COLOR SHIFTING
    6-4 INK DROPS ON THE MEDIA
    6-5 VERTICAL BANDING
    6-6 MISSING DOT OR DEFLECTED-FIRED DOT APPEARS WHEN PERFORMING PRINTING AFTER LEAVING THE MACHINE UNUSED FOR A LONG TIME
    6-7 MEDIA SKEW
    6-8 MOTOR ERROR
    6-9 HEATER / DRYER TEMPERATURE DOES NOT GO UP
    6-10 THE BLOWER FAN DOES NOT OPERATE
    6-11 THE TAKE-UP UNIT DOES NOT OPERATE
    6-12 PROBLEM IN NETWORK (RIP DOES NOT RECOGNIZE THE PRINTER)
    6-13 ERROR MESSAGE
    6-14 SERVICE CALL

    7) Service Activities
    7-1 INSTALLATION CHECK LIST
    7-2 MAINTENANCE CHECK LIST
    7-3 SPECIFICATION