Mimaki JV22-130 Mimaki JV22-160 Service Manual

Service Manual Mimaki JV22-130 Mimaki JV22-160;
This manual is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Mimaki.
You can print, zoom or read any diagram, picture or page from this Service Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Mimaki JV22-130 Mimaki JV22-160. You can find easily everything what do you need.
To see what contain, please read table of contents:

CHAPTER 1. OVERVIEW OF MAINTENANCE
1-1. Cautions in maintenance
1-2. How to use this maintenance manual
1-3. Tools required for maintenance works
1-4. Names of parts
1-4-1. Front face
1-4-2. Rear face
1-5. Specifications

CHAPTER 2. EXPLANATION OF OPERATION
2-1. Explanation of electrical components
2-1-1. Operations
2-1-2. Power supply
2-1-3. Main PCB
2-1-4. 1394 PCB
2-1-5. I/F Connection PCB
2-1-6. IO PCB
2-1-7. Slider PCB
2-1-8. Linear encoder PCB
2-1-9. The Keyboard PCB
2-1-10. Take-up motor PCB
2-2. Ink system
2-2-1. Definitions
2-2-2. Brief explanation of the ink system
2-2-3. Parameters related to the ink system
2-3. Brief explanation of media size detection control

CHAPTER 3. TROUBLESHOOTING
3-1. Troubles for which error messages are given on the LCD
3-2. Error messages and corrective measures
3-2-1. Error messages for troubles for which error numbers are given on the LCD
3-2-2. Ink-related components and other components
3-3. Troubles for which error messages are not given on the LCD
3-3-1. The device will not be energized
3-3-2. The device fails to perform plotting
3-3-3. Cutting failure
3-3-4. Faulty cutter
3-3-5. Abnormal vacuum fan
3-3-6. Abnormal nozzle discharge
3-3-7. Abnormal ink shot
3-3-8. Ink-filling cannot be performed
3-3-9. Abnormal wiper operation
3-4. Plotting failure
3-4-1. Print is not sharp
3-4-2. Abnormal print
3-4-3. Color of print is pale
3-4-4. Plotted drawing is out of position
3-4-5. Plotted dots or lines are dirty
3-4-6. Stripes are always drawn at the time of scanning
3-4-7. Black and White Stripes appear from side to side
3-4-8. Dark and Light Images Occur at Each Scan
3-4-9. Unstable heater temperature
3-4-10. Ink drop or mist

CHAPTER 4. ADJUSTMENT
4-1. Maintenance Flow by Replacement Parts
4-2. Maintenance item
4-2-1. Adjustment of the X-motor coupling
4-2-2. Replacement Print head unit
4-2-3. Replacement Print head assy
4-2-4. Adjustment of the head angle
4-2-5. Adjustment of the head unit
4-2-6. Replacement of pump assy and cap slider assy
4-2-7. Changing the head height (High/Low range)
4-2-8. Adjustment of the station height
4-2-9. Adjustment of the cutter height
4-2-10. Adjustment of the Head sensor height
4-2-11. Adjustment of the Linear sensor PCB assy height
4-2-12. Adjustment of the Y-motor belt tension

CHAPTER 5. MAINTENANCE MODE
5-1. Maintenance items
5-2. Entering into the maintenance mode
5-2-1. Entering into the maintenance mode when actuating the plotter
5-2-2. Entering into the maintenance mode by system parameters
5-3. Menu of #ADJUST
5-3-1. PRINTadjust2
1. Y Base
2. Y Single (Y Repeat, Y Bi-Directional)
3. FINE Y Si. (FINE Y Re., FINE Y Bi.)
4. X DIRECTION
5-3-2. HEAD ADJUST
5-3-3. WASH
5-3-4. REPLACE COUNTER
5-3-5. DEFAULT SET
5-3-6. CAPPING
5-3-7. HEAD HEIGHT
5-3-8. INK SETUP
5-3-9. HEAD ID
5-3-10. MOTOR CURRENT
5-3-11. SERIAL NO
5-3-12. DEALER NO
5-3-13. WORM WHEEL
5-3-14. ADJUST EDGE
5-3-15. 500mmSQUARE
5-3-16. SET QUALITY
5-3-17. MEDIA COMP2
5-4. #TEST items
5-4-1. CHECK PATTERN
PATTERN : NOZZLE
5-4-2. PARAMETER DRAW
5-4-3. ALL PATTERN
5-4-4. X SERVO
5-4-5. Y SERVO
5-4-6. XY SERVO
5-4-8. ACTION TEST
5-4-9. SENSOR TEST
5-4-10. PAPER SENSOR
5-4-11. KEYBOARD TEST
5-4-12. LCD TEST
5-4-13. PUMP MOTOR
5-4-14. TIMER CHECK
5-4-15. MEMORY CHECK
5-4-16. SKEW CHECK
5-4-17. TEMP CHECK
5-4-18. ENCODER CHECK
5-5. #PARAMETER items
5-5-1. SYSTEM PARAMETER
5-5-2. INK PARAMETER 1
5-5-3. INK PARAMETER 2
5-5-4. INK PARAMETER 3
5-5-5. INK PARAMETER 4
5-5-6. INK PARAMETER 5
5-5-7. MAINTENANCE PARAMETER
5-5-8. CUSTOM PARAMETER
5-5-9. SERVO PARAMETER
5-5-10. ADJUSTMENT PARAMETER
5-6. Uploading and Downloading Parameters
5-6-1. UPLOAD (Plotter >>> Computer)
5-6-2. DOWNLOAD (Computer >>> Plotter)
5-6-3.Error messages
5-7. Updating the firmware
5-7-1. The firmware in this unit
5-7-2. Main unit side firmware version updating file
5-7-3. Interface side firmware version updating file
5-7-4. Checking the version updating file
5-7-5. Updating procedure

APPENDIX
6-1. Maintenance menu tree
6-2. Electrical component block diagram

Number of pages: 154.